Gigabyte GA-6LISL Manual - Page 27

BMC_LED1 BMC Firmware Readiness LED, BAT Battery cable connector

Get Gigabyte GA-6LISL PDF manuals and user guides View all Gigabyte GA-6LISL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

20) BMC_LED1 (BMC Firmware Readiness LED) State Description On BMC firmware is initial Blinking BMC firmware is ready Off System is powered off 21) BAT (Battery cable connector) The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost. 2 1 Pin No. 1 2 Definition RTC Reset GND • Always turn off your computer and unplug the power cord before replacing the battery. • Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model. • Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncer- tain about the battery model. • When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the bat- tery (the positive side should face up). • Used batteries must be handled in accordance with local environmental regulations. - 27 - Hardware Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
- 27 -
Hardware Installation
20) BMC_LED1 (BMC Firmware Readiness LED)
State
Description
On
BMC firmware is initial
Blinking
BMC firmware is ready
Off
System is powered off
21) BAT (Battery cable connector)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a
low level, or the CMOS values may not be accurate or may be lost.
1
2
Pin No.
Definition
1
RTC Reset
2
GND
•
Always turn off your computer and unplug the power cord before replacing the battery.
•
Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect
model.
•
Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncer-
tain about the battery model.
•
When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the bat-
tery (the positive side should face up).
•
Used batteries must be handled in accordance with local environmental regulations.