Gigabyte GA-F2A68HM-DS2H User Manual - Page 14
SATA3 0/1/2/3 SATA 6Gb/s Connectors, F_PANEL Front Panel Header
View all Gigabyte GA-F2A68HM-DS2H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
DEBUG PORT 5) SATA3 0/1/2/3 (SATA 6GDbE/sBUCGonnectDoErBsU)G The SATA connectors conforPmORtTo SATA 6GPbO/RsTstandard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The AMD Chipset supports RAID 0, RAID 1, RAID 10, and JBOD. Refer to Chapter 3, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array. 1 Pin No. Definition Pin No. Definition 1 GND 5 RXN 2 TXP 6 RXP SATA3 2 3 3 TXN 4 GND 7 GND SATA3 0 1 7 1 7 •• A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number. •• A RAID 10 configuration requires four hard drives. •• To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA Configuration," for more information. 6) F_PANEL (Front Panel Header) Connect the power switch, reset switch, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. Power LED Power Switch Speaker •• PLED/PWR_LED (Power LED): PLED+ PLED- PW+ PWSPEAK+ NC NC SPEAK- System Status LED Connects to the power status indicator on F_ 2 1 S0 On S3/S4/S5 Off 20 F_ 19 •• PW (Power Switch): the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 sleep state or powered off (S5). S S U 123 HD+ HD- RESRES+ CICI+ PWR_LED+ PWR_LED- Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information). •• SPEAK (Speaker): Hard Drive Reset Activity LED Switch Power LED Chassis Intrusion Header Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. •• HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading S or writing data. 1 •• RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the _S computer freezes and fails to perform a normal restart. •• CI (Chassis Intrusion Header): Connects to the chassis intrusion switch/se_nsor on the chassis that can detect if the BchSa_ssis cover has been removed. This function requires a chassis wBith a chassis intrusion switch/sensor. B S •• NC: No connection. 1 23 1 1 23 1 1 23 1 The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, hard drive activity LED and etc. When connecting your chassis front panel module to this header, make sure the 1 23 wire assignments and the pin assigSnmB_ents are matched correctly. B - 14 - _S S_ _ B