Gigabyte GA-M68MT-S2P Manual - Page 64

B. Configuring SATA controller mode in BIOS Setup, Integrated Peripherals, NV Serial-ATA Controller

Get Gigabyte GA-M68MT-S2P PDF manuals and user guides
UPC - 818313010995
View all Gigabyte GA-M68MT-S2P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

B. Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Step 1: Turn on your computer and press to enter BIOS Setup during the POST (Power-On Self-Test). Under Integrated Peripherals, make sure NV Serial-ATA Controller is enabled. To enable RAID, go to the Serial-ATA RAID Config (Figure 1). CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Integrated Peripherals On-Chip IDE Channel NV Serial-ATA Controller IDE Prefetch Mode USB Memory Type } Serial-ATA RAID Config Onboard Audio Function On-Chip MAC Lan Onboard LAN Boot ROM Onboard Serial Port 1 Onboard Parallel Port Parallel Port Mode x ECP Mode Use DMA On-Chip USB USB Keyboard Support USB Mouse Support Legacy USB storage detect [Enabled] [Enabled] [Enabled] [SHADOW] [Press Enter] [Auto] [Auto] [Disabled] [3F8/IRQ4] [378/IRQ7] [SPP] 3 [V1.1+V2.0] [Disabled] [Disabled] [Enabled] Item Help Menu Level  Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Figure 1 ESC: Exit F1: General Help F7: Optimized Defaults Set NV SATA RAID function to Enabled to enable RAID control for each SATA connector. Then enable the SATA channels with hard drives that you want to use for RAID (for example, NV SATA 1 Primary RAID con- trols the SATA2_0 connector and NV SATA 1 Secondary RAID controls the SATA2_1 connector) (Figure 2). CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Serial-ATA RAID Config NV SATA RAID function NV SATA 1 Primary RAID NV SATA 1 Secondary RAID NV SATA 2 Primary RAID NV SATA 2 Secondary RAID [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] Item Help Menu Level  Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Step 2: Save changes and exit BIOS Setup. Figure 2 ESC: Exit F1: General Help F7: Optimized Defaults The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. Appendix - 64 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Appendix
- 64 -
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test).
Under
Integrated Peripherals
, make sure
NV Serial-ATA Controller
is enabled. To enable RAID, go to the
Serial-ATA RAID Config
(Figure 1).
Step 2:
Save changes and exit BIOS Setup.
Figure 1
The BIOS Setup menus described in this section may differ from the exact settings for your moth-
erboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you
have and the BIOS version.
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Integrated Peripherals
On-Chip IDE Channel
[Enabled]
NV Serial-ATA Controller
[Enabled]
IDE Prefetch Mode
[Enabled]
USB Memory Type
[SHADOW]
Serial-ATARAID Config
[Press Enter]
Onboard Audio Function
[Auto]
On-Chip MAC Lan
[Auto]
Onboard LAN Boot ROM
[Disabled]
Onboard Serial Port 1
[3F8/IRQ4]
Onboard Parallel Port
[378/IRQ7]
Parallel Port Mode
[SPP]
x
ECP Mode Use DMA
3
On-Chip USB
[V1.1+V2.0]
USB Keyboard Support
[Disabled]
USB Mouse Support
[Disabled]
Legacy USB storage detect
[Enabled]
higf
: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Item Help
Menu Level
Set
NV SATA RAID function
to
Enabled
to enable RAID control for each SATA connector. Then enable the
SATA channels with hard drives that you want to use for RAID (for example,
NV SATA 1 Primary RAID
con-
trols the SATA2_0 connector and
NV SATA 1 Secondary RAID
controls the SATA2_1 connector) (Figure 2).
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Serial-ATA RAID Config
NV SATA RAID function
[Enabled]
NV SATA 1 Primary RAID
[Enabled]
NV SATA 1 Secondary RAID
[Enabled]
NV SATA 2 Primary RAID
[Disabled]
NV SATA 2 Secondary RAID
[Disabled]
higf
: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Item Help
Menu Level

Figure 2