Gigabyte GA-MA790FX-DQ6 Manual - Page 95

B. Installing Windows Vista

Get Gigabyte GA-MA790FX-DQ6 PDF manuals and user guides View all Gigabyte GA-MA790FX-DQ6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

English B. Installing Windows Vista (Note) (The procedure below assumes that only one RAID array exists in your system.) AMD SB600 SATA controllers: Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears (RAID hard drive will not be detected at this stage), select Load Driver. (Figure 8). Figure 8 Step 2: Specify the location where the driver is saved. Refer to the following two ways: Method A: Insert the motherboard driver disk into your system and browse to the following directory: \Chipset\RS690\Vista\Packages\Drivers\SBDrv\SB6xx\RAID\LH For Windows Vista 64-bit, browse to the LH64A folder. Method B: If you have copied the SATA RAID driver to a floppy disk following the instructions in "5-1-3," insert the floppy disk and browse to the LH (for Windows Vista 32-bit) or LH64A (for Windows Vista 64-bit) folder (Figure 9). Figure 9 (Note) For AHCI drives, installation of Windows Vista does not require you to install the SATA AHCI driver during the OS installation process. - 95 - Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Appendix
- 95 -
English
B. Installing Windows Vista
(Note)
(The procedure below assumes that only one RAID array exists in your system.)
AMD SB600 SATA controllers:
Step 1:
Restart your system to boot from the Windows Vista setup disk and perform standard OS installation
steps. When a screen similar to that below appears (RAID hard drive will not be detected at this stage),
select
Load Driver
. (Figure 8).
Figure 8
Step 2:
Specify the location where the driver is saved. Refer to the following two ways:
Method A:
Insert the motherboard driver disk into your system and browse to the following directory:
\Chipset\RS690\Vista\Packages\Drivers\SBDrv\SB6xx\RAID\LH
For Windows Vista 64-bit, browse to the
LH64A
folder.
Method B:
If you have copied the SATA RAID driver to a floppy disk following the instructions in "5-1-3,"
insert the
floppy disk and browse to the
LH
(for Windows Vista 32-bit) or
LH64A
(for Windows Vista 64-bit) folder
(Figure 9).
Figure 9
(Note)
For AHCI drives, installation of Windows Vista does not require you to install the SATA AHCI
driver during the OS installation process.