Gigabyte Z390 UD User Manual - Page 42

A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode

Get Gigabyte Z390 UD PDF manuals and user guides View all Gigabyte Z390 UD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode If the SATA controller has been configured in Intel RST Premium With Intel Optane System Acceleration mode, please follow the steps below: 1. After system restarts, go to the BIOS Setup, make sure CSM Support under the BIOS menu is disabled. 2. Go to Peripherals\SATA And RST Configuration and make sure USE RST Legacy OROM is disabled. If you want to enable the Optane™ memory installed in the M2A connector, set PCIe Storage Dev on Port 9 to RST Controlled. 3. Enter the operating system, launch the Intel® Rapid Storage Technology utility from the Start menu, and then enable Intel® Optane™ Memory on the Intel® Optane™ Memory tab. 4. Launch the Intel® Rapid Storage Technology utility from the Start menu and make sure the Intel® Optane™ Memory has been enabled. If you want to accelerate the system drive, you can select specific folders, files, or applications to accelerate using the Intel® Optane™ Memory Pinning function. (The Optane™ memory used must have at least 32 GB capacity.) •• An Optane™ memory cannot be used to accelerate an M.2 PCIe SSD. •• Do not abruptly remove the Optane™ memory. Doing so will cause the operating system to stop functioning correctly. •• If you want to change/remove the Optane™ memory, you must disable it using the Intel® Rapid Storage Technology or Intel(R) Optane Memory application first. •• After enabling the Optane™ memory, the related BIOS settings will remain even after a BIOS update. - 42 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode
If the SATA controller has been configured in Intel RST Premium With Intel Optane System Acceleration mode,
please follow the steps below:
1. After system restarts, go to the BIOS Setup, make sure
CSM Support
under the
BIOS
menu is disabled.
2. Go to
Peripherals\SATA And RST Configuration
and make sure
USE RST Legacy OROM
is disabled.
If you want to enable the Optane
™
memory installed in the M2A connector, set
PCIe Storage Dev on Port
9
to
RST Controlled
.
3. Enter the operating system, launch the I
ntel
®
Rapid Storage Technology
utility from the Start menu, and
then enable Intel
®
Optane
™
Memory on the
Intel
®
Optane
™
Memory
tab.
4. Launch the Intel
®
Rapid Storage Technology utility from the Start menu and make sure the Intel
®
Optane
™
Memory has been enabled. If you want to accelerate the system drive, you can select specific folders, files,
or applications to accelerate using the
Intel
®
Optane
™
Memory Pinning
function. (The Optane
™
memory
used must have at least 32 GB capacity.)
•
An Optane
™
memory cannot be used to accelerate an M.2 PCIe SSD.
•
Do not abruptly remove the Optane
™
memory. Doing so will cause the operating system to stop
functioning correctly.
•
If you want to change/remove the Optane
™
memory, you must disable it using the Intel
®
Rapid
Storage Technology or Intel(R) Optane Memory application first.
•
After enabling the Optane
™
memory, the related BIOS settings will remain even after a BIOS update.
- 42 -