Haier DW12-LBE User Manual - Page 7

Starting the Appliance Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ONOFF button (A) located on the control pannel. The appliance is on. Setting and Starting a wash Cycle Select the desired cycle by pressing programme selection button (F). Each time the button is pressed, the seletion cursor"Q"will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual. After press the startpause button(E), the wash cycle has begun and can no longer be changed. If necessary, read the paragraph entitled "Cancelling or modifying a cycle" Cancelling or modifying a cycle A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). To modify a cycle that is already underway, press the start- pause button (E) for 5 second, all of the settings will be cancelled. To set a new cycle, follow the instructions contained in the paragraph entitled "Setting and starting a wash cycle". Wash Cycle Program Light The dishwasher is equipped with a LCD indicator light (G) that turns on when the appliance is running the wash cycle. At the end of the wash cycle Six beeps will indicate that the wash cycle has finished and the LCD display (B) will come on (see fig.1). Turn off the appliance using the ON-OFF button. Turn off the water supply to the appliance and open the door. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. Setting the Wash Cycle with a Delayed Start Time By pressing the "D" button (see close-up view-'Control panel"), select ,and the selection cursor turns on,then pressing the "C" button ,the start of wash can be delayed for between 1 to 12 hours. Each time the button is pressed, the display (M) will show the number of hours for the delay period. Choose the amount of time desired. After selecting the wash cycle, pressing the startpause button(E), the delay time on the display will blink.This indicates that the countdown has begun. After the time has alapsed, the cycle will start. NOTE: During the delay period, it is preferable not to change any of the settings, If this is necessary, all of the settings must be cancelled by pressing the ON/OFF button (A). At this point, all of the steps for "setting the wash cycle with a Delayed Start Time" and "Setting and Starting a wash cycle" must be repeated, following the instructions contained in the corresponding sections. If the door is opened to the unit during the delay period, the countdown will stop. It wil begin again when the door is closed. All of the wash cycle set to reverse time function, we may in focus start circulate time. Wash Cycle adjustment Buttons Button for "extre drying" or "half load" or "delay" By pressing the "D" button in sequence ,the selection cursor (Q) will come on in turn : Extre drying -- Half load --Delay -- Extre drying+Half load --Extre drying+Delay --Half load +Delay -- Extre drying+Half load + Delay Extre drying By pressing the "D" button,the drying time of extre drying will be longer ,and the drying relating is better. Half load By pressing the "D" button,this button (see "close-up View - Control Panel", letter "D") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and power. It can be used before setting any of the wash cycle, except for the intensive cycle ( if included in the wash cycle table). Please keep in mind that the amount of detergent should also be cut in half The dishwasher is equipped an indecation "P" comprissing 4 symbels which represerd the diferent phases of a wash cycle. When the wash cycle has started,the displace will indicate ,the phase under way in sequence.There place are pre-wash,wash, rinse,drying. pre-wash wash rinse drying .6. GB