Haier WQP12-AFM2 User Manual - Page 2

Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. - The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. - Fundamental rules to follow when using the appliance: * Never touch the dishwasher when bare foot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be exces- sively or dangerously bent or flattened; * If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply. - Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open. - This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. - Do not touch the heating element during or after a wash cycle. - Do not lean or sit on the door when it is open, as this could overturn the dishwasher. - If the appliance malfunctions, turn off water supply to the appli- ance and disconnect the plug from the wall socket. Then, consult the section entitled, "Troubleshooting. "If you can not solve the problem, contact a service centre. - Only specialised personnel are authorised to make repairs. - Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. - The appliance must be positioned so that the plug is accessible. - The carpet must not obstruct the opening when the appliance installing on the ground with carpet. - If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. Close-up View (Control Panel) A BC F A ON-OFF Light B ON-OFF Button C Low Salt Indicator Light E D D Knob For Selecting Cycle E Handle For Opening Door F "Eco" Button .1. GB Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level. In any case, the appliance should not be inclined more than 2 . If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see fig.1/ A). Some models have an "Acquablock" water supply pipe (see fig.1/B) with filter in the threaded inlet. If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see fig.C). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. fig.C Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Fig.1/A Fig.1/ B Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adaptors or the like as they could cause overheating and burns. GB .10.