Harman Kardon HK3300 Owners Manual - Page 7

klera.11

Get Harman Kardon HK3300 PDF manuals and user guides View all Harman Kardon HK3300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

INSTALLATION O 9D coca 0 klera.11 r6"4.1 AC Power Plug the cord into a wall socket. NOTE: The power does not shut off completely by just turning the power off. So power cord should be removed from AC outlet when not in use for a prolonged time. AC Voltage Selector This receiver is supplied with a voltage selector enabling selection between 230V and 240V on the rear panel. If the selector is not set to the local voltage. set the selector to the correct voltage with a screwdriver before connecting the powr cord to a mains outlet. Connecting Speakers 1. For best performance, use high quality speaker cables. However, ordinary copper wire can be used if the gauge meets the following requirements: Wire Length Gauge Up to 2m (8 feet) 18 AWG Up to 4m (12 feet) 16 AWG Up to 7m (20 feet) 14 AWG Over 7m (20 feet) 10-12 AWG custom speaker cable 2. Avoid coiling excess wire with or near line level hook-up cords. 3. Note the difference between the two conductors in each cable: different colored insulation, ridged insulation, or colored yarn. Connect the right-hand speaker to the receiver, being careful to connect the positive terminal on the speaker to the terminal marked "Right" on the receiver, and the negative or ground terminal on the speaker to the corresponding "GND" terminal on the receiver. 4. Connect terminals on the left-hand speaker to the "Left" and corresponding "GND" terminals on the receiver, again being careful to maintain correct polarity. 5. If you are using a second set of speakers, connect them in the same way to the terminals marked "Speaker System 2." 5 RIGHT SPEAKER SYSTEM 1 GND GND LEFT O SPEAKER SYSTEM 2 RIGHT GND GND LEFT CAUTION SPEAKER IMPEDANCE ATTENTION IMPEDANCE DES HAST-PARLEURS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
INSTALLATION
O
9D
coca
AC
Power
Plug
the
cord
into
a
wall
socket.
NOTE:
The
power
does
not
shut
off
completely
by
just
turning
the
power
off.
So
power
cord
should
be
removed
from
AC
outlet
when
not
in
use
for
a
prolonged
time.
AC
Voltage
Selector
This
receiver
is
supplied
with
a
voltage
selector
enabling
selection
between
230V
and
240V
on
the
rear
panel.
If
the
selector
is
not
set
to
the
local
voltage.
set
the
selector
to
the
correct
voltage
with
a
screwdriver
before
connecting
the
powr
cord
to
a
mains
outlet.
0
r6"4.1
klera.11
Connecting
Speakers
1.
For
best
performance,
use
high
quality
speaker
cables.
However,
ordinary
copper
wire
can
be
used
if
the
gauge
meets
the
following
requirements:
Wire
Length
Gauge
Up
to
2m
(8
feet)
18
AWG
Up
to
4m
(12
feet)
16
AWG
Up
to
7m
(20
feet)
14
AWG
Over
7m
(20
feet)
10-12
AWG
custom
speaker
cable
2.
Avoid
coiling
excess
wire
with
or
near
line
level
hook-up
cords.
3.
Note
the
difference
between
the
two
conductors
in
each
cable:
different
colored
insulation,
ridged
insulation,
or
colored
yarn.
Connect
the
right-hand
speaker
to
the
receiver,
being
careful
to
connect
the
positive
terminal
on
the
speaker
to
the
terminal
marked
"Right"
on
the
receiver,
and
the
negative
or
ground
terminal
on
the
speaker
to
the
corresponding
"GND"
terminal
on
the
receiver.
4.
Connect
terminals
on
the
left-hand
speaker
to
the
"Left"
and
corresponding
"GND"
terminals
on
the
receiver,
again
being
careful
to
maintain
correct
polarity.
5.
If
you
are
using
a
second
set
of
speakers,
connect
them
in
the
same
way
to
the
terminals
marked
"Speaker
System
2."
SPEAKER
SYSTEM
1
O
SPEAKER
SYSTEM
2
RIGHT
GND
GND
LEFT
RIGHT
GND
GND
LEFT
CAUTION
SPEAKER
IMPEDANCE
ATTENTION
IMPEDANCE
DES
HAST-PARLEURS
5