Hayward Aqua Plus® Model: PL-PLUS-16V Installation - Page 4

Introduction Before You Begin What's Included Before attempting to install the Aqua Plus 16v system, check that the following components have been included in the package: Aqua Plus 16v Electronics Unit (3) Temperature sensors with 15 ft. (5m) cable, hose clamp T-CELL-15 Turbo Cell and Flow Switch with 15 ft. cables PVC unions What's NOT Included Some of the additional items that you may need to complete an installation include: Circuit breakers None are included with control-see page 12 and inside of door for suitable breakers Wire 4-conductor cable (electronics unit to remote display/keypad) Wire/conduit for 100A service from main panel to Aqua Plus 16v Wire/conduit for filter pump and other high voltage loads Wire for bonding Miscellaneous Utility electrical outlet and weatherproof cover (for mounting on side of Aqua Plus 16v) Mounting hardware (screws, etc.) for mounting Aqua Plus 16v and remote display/keypad Valves (use standard Hayward, Pentair/Compool, or Jandy valves) Additional valve actuators Accessory Products - Order Separately AQL-CHEM ORP & pH sense kit AQL-CHEM2(-240) pH dispense kit AQL2-Wx-PS-16 Wired Remote Display AQL2-POD Handheld Wireless Remote Control AQL2-Wx-RF-PS-16 Wireless Wallmount Remote Control AQL2-Tx-RF-PS-16(x=W/B) Wireless Table Top Remote Control, specify color - white or black AQL-SS-6B-x (x=W/B) Wired Spa Side 6 Function Remote Control, 150ft cable, spec. color (white or black) AQL-SS-D-x (x=W/B) Wired Spa Side 8 Function Remote Control, 150ft cable, spec. color (white or black) AQL2-SS-RF Wireless Spa Side Remote Control AQL2-BASE-RF Base Station AQL-DIM Light Dimmer Relay AQL-COLOR-MODHV Color Network Module for 120V Generation 4 ColorLogic lights GVA-24 Valve Actuator V&A-xx Valve & Actuator (xx=1P (1.5" pos. seal), -2P (2" pos. seal)) GLX-PC-12-KIT 10K thermistor sensor w/15' leads, (necessary if both solar and dual equipment is desired) NOTE: Before installing this product as part of a saline water purification system in a pool or spa using natural stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist should be consulted regarding the appropriate type, installation, sealant (if any) and maintenance of stone used around a saline pool with electronic chlorine generator in your particular location and circumstances. NOTE: The use of dry acid (sodium bisulfate) to adjust pool pH is discouraged especially in arid regions where pool water is subject to excessive evaporation and is not commonly diluted with fresh water. Dry acid can cause a buildup of by-products that can damage your chlorinator cell. 1 3. Once the heater is running, you can verify the "heater cooldown" feature (optional - see Configuration Menu/ Heater Config.) is operating properly: • Press the "Filter" button once (for 2 speed pumps, this may require 2 pushes of the "Filter" button). • The heater should turn off ("Heater" LED off) and the "Filter" LED will flash to indicated heater cooldown is active. • The display will periodically indicate that the filter pump is on for heater cooldown and show the minutes remaining. • The pump will automatically turn off at the end of the 5 minute heater cooldown period. For more detailed instructions on control and operation of the Aqua Plus 16v system, refer to the Operation Manual. Service Mode Service mode disables all automatic control operation and is intended to be used when servicing the pool system. To enter service mode, push the SERVICE button once on the main unit keypad. This will initially turn all outputs off and then allow you to turn outputs on/off manually at the main display (only). In service mode, the buttons on the optional remote display/keypad and the optional spa side remote will turn outputs off, but will not turn any output on. Heater control outputs and solar control outputs are prevented from turning on if the water temperature exceeds 104ºF (40ºC). Pushing the SERVICE button again will enter a timed service mode. Service operation as described above will continue for 3 hours, then automatically return to normal operation. Push the SERVICE button once more to exit out of Service mode. 42