Hayward AquaRite® 120 Operation Manual - Page 5

Input power for use with Hayward/Goldline, Pentair and Polaris controls Wire the Aqua Rite® DIRECTLY to 120/240VAC power (not through timer or relay). HAYWARD/GOLDLINE, PENTAIR or POLARIS AQUA RITE (240 VAC) AQUA RITE (120 VAC) SUBPANEL GND GND NEUTRAL GROUND PCB BONDING LOOP PCB BONDING LOOP Optional Hayward/Goldline, Pentair and Polaris controls: The Hayward/Goldline, Pentair and Polaris controls use a 4 wire connection to communicate to the Aqua Rite and can be wired up to 500' apart. Any outdoor rated 4 conductor cable can be used. Refer to each manufacturer's instructions and the wiring diagrams below for proper wiring connection to the Aqua Rite. NOTE: There must be only 1 "primary" unit. All other Aqua Rite units must be configured as "secondary". 4 GREEN 3 YELLOW 2 BLACK 1 RED Jumper Installed For Primary (Factory Default) Jumper Removed For Secondary(s) Additional Aqua Rite(s) (if required) Hayward/Goldline, Pentair or Polaris Power Center Aqua Rite (Primary) Aqua Rite (Secondary) Hayward/Goldline - Attach wires to proper screw terminals as shown below. GRN 4 Aqua Rite YEL BLK 3 2 RED 1 green 4 GRN yellow 3 YEL Pro Logic black 2 BLK Aqua Logic red 1 RED Pentair - Attach wires to opposite numbered screw terminals as shown below. Note that the colors marked on the Pentair PCB do not match the Aqua Rite. GRN 4 Aqua Rite YEL 3 BLK 2 RED 1 (Colors Do Not Match) green marking on PCB 1 BLK / GND yellow 2 GRN / -DT Intellitouch black 3 YEL / +DT red 4 RED / +15 13 Water Chemistry The table below summarizes the levels that are recommended by The Association of Pool and Spa Professionals (APSP). The only special requirements for the Aqua Rite are the salt level and stabilizer. It is important to maintain these levels in order to prevent corrosion or scaling and to ensure maximum enjoyment of the pool. Test your water periodically. Your Authorized Aqua Rite Dealer (AARD) or most pool stores can provide you with the chemicals and procedures to adjust the water chemistry. Be sure to tell the pool store that you are using an Aqua Rite chlorine generator. Saturation index The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool water "balance". Your water is properly balanced if the Si is 0 ±.2. If the Si is below -0.2, the water is corrosive and plaster pool walls will be dissolved into the water. If the Si is above +0.2, scaling and staining will occur. Use the chart below to determine the saturation index. Si = pH + Ti + Ci + Ai - 12.1 ºC ºF Ti Calcuim Hardness Ci Total Alkalinity Ai 12 53 .3 75 1.5 75 1.9 100 1.6 100 2.0 16 60 .4 125 1.7 125 2.1 19 66 .5 150 1.8 150 2.2 200 1.9 24 76 .6 250 2.0 200 2.3 250 2.4 29 84 .7 300 2.1 400 2.2 34 94 .8 600 2.4 300 2.5 400 2.6 600 2.8 39 103 .9 800 2.5 800 2.9 How to use: Measure pool pH, temperature, calcium hardness, and total alkalinity. Use the chart above to determine Ti, Ci,and Ai from your measurements. Insert values of pH, Ti, Ci and Ai into the above equation. If Si equals .2 or more, scaling and staining may occur. If Si equals -.2 or less corrosion or irritation may occur. -.2 0 .2 CORROSIVE SCALING OK 2