Hayward Star-Clear™ Plus Model: ALL MODELS - Page 3

TO REDUCE THE RISK OF ENTRAPMENT HAZARDS:  A minimum of two functioning suction outlets per pump must be installed. Suction outlets in the same plane (i.e. floor or wall), must be installed a minimum of three feet (3') [1 meter] apart, as measured from near point to near point.  Dual suction outlets shall be placed in such locations and distances to avoid "dual blockage" by a user.  Dual suction outlets shall not be located on seating areas or on the backrest for such seating areas.  The pool or spa circulation system shall be designed to comply with ANSI/APSP-7 2006.  Suction outlet covers shall conform to ANSI/ASME A112.19.8  Never use Pool or Spa if any suction outlet component (cover/grate) is damaged, broken, cracked, missing, or not securely attached.  Immediately replace damaged, broken, cracked, missing, or not securely attached suction outlet components.  The CPSP as well as the ICC International Residential Code Part IX, Appendix G, Section AG106 specifies the installation of a safety vacuum release system conforming to ASME A112.19.17, or an approved gravity drain system.  Failure to remove pressure test plugs and/or plugs used in winterization of the pool/spa from the suction outlets can result in an increased potential for suction entrapment.  Failure to keep suction outlet components clear of debris, such as leaves, dirt, hair, paper and other material can result in an increased potential for suction entrapment. Suction outlet covers and grates have a finite life. They should be inspected frequently and replaced within specified life. GENERAL INFORMATION The Hayward Star-Clear Plus filter is a high performance swimming pool filter with a residential filtration rating of 4,500 gallons (17 kl) per hour (C751), 5,400 gallons (20.5 kl) per hour (C900), or 7,200 gallons (27.3 kl) per hour (C1200, C1502, C1750, and C2002). Manufactured from durable, corrosion-proof materials, they are designed for continuous or intermittent operation, for installation above or below the pool water line, for fresh or saltwater swimming pools or spas. Star-Clear Plus filters utilize a reusable single element, reinforced polyester filter cartridge to provide a high degree of water clarity with absolute minimum care. Their unique design is such that no tools are needed to remove or replace the cartridge in the filter assembly. Simply spin off the locking knob, lift off the filter cover and remove the cartridge. It's that easy. PUMP SELECTION AND LOCATION To power your Star-Clear Plus filter, select a continuous duty pump designed for swimming pool or spa service. It is important to first determine where your pump and filter will be located. If above the water line, a self-priming pump must be used. Self-priming pumps such as Hayward's Super Pump®, Super II, or TriStar have the ability to lift water from a lower level and prime automatically. Select a pump appropriate for your application. Taking into consideration, operation of hydrotherapy fittings, automatic cleaners, required turn over rates and losses in the system. A dealer can help you select the proper size pump for your system. FILTER LOCATION 1. Since plumbing fittings offer a resistance to water flow, position the filter as close to the swimming pool as local codes allow. Keep the number of fittings to a minimum. Select a well drained area, one that will not flood when it rains. 2. Set the filter on a solid level surface. Allow a minimum top clearance for cartridge removal of 19" (483mm) for the C751 and C900, 25" (635mm) for the C1200, C1502 and allow 30" (762mm) for the C1750 and C2002. Be sure filter, pump, drain & pressure gauge are accessible for convenient operation. 3. Position the filter so the tank can drain by gravity. 4. If practical, place pump and filter in the shade to shield it from continuous, direct heat from the sun. Page 3 of 8 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS STAR-CLEAR PLUS CARTRIDGE FILTER ISC1750 REV C