Hayward TriStar VS 950 2.70 THP VS Pump Family - Owners Manual - Page 26

Low Flow - Generally, Noisy Pump, Interference With Home Automation/Power Line Communication

Page 26 highlights

5. Suction side clogged. Contact a qualified repair professional. You should have 5" - 6" of vacuum at the strainer cover (your pool dealer can confirm this with a vacuum gauge). You may be able to check by removing the skimmer basket and holding an object over the bottom port with the skimmer full and the pump running. If no suction is felt, check for line blockage. a. If the pump develops a vacuum, check for a blocked suction line or a dirty strainer basket. An air leak in the suction piping may be the cause. b. If the pump does not develop a vacuum and the pump has sufficient "priming water": i. Re-check the strainer housing cover and all threaded connections for suction leaks. Check if all system hose clamps are tight. ii. Check voltage to ensure that the motor is rotating at full rpm's. iii. Open the housing cover and check for clogging or obstruction in suction. Check the impeller for debris. iv. Remove and replace the shaft seal only if it is leaking. • Low Flow - Generally: 1. Clogged or restricted strainer or suction line. Contact a qualified repair professional. 2. Undersized pool piping. Correct the piping size. 3. Plugged or restricted discharge line of filter, valve partially closed (high gauge reading). Sand filters - backwash as per manufacturer's instructions; D.E. filters - backwash as per manufacturer's instructions; Cartridge filters - clean or replace the cartridge. 4. Air leak in suction (bubbles issuing from return fittings). Re-tighten the suction and discharge connections using PTFE tape. Inspect other plumbing connections, and tighten as required. 5. Plugged, restricted, or damaged impeller. Replace the impeller including a new seal assembly. • Noisy Pump: 1. Air leak in suction piping, cavitations caused by restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted discharge return lines. Correct the suction condition or throttle return lines, if practical. Holding your hand over the return fitting will sometimes prove this, or by putting in a smaller eyeball fitting. 2. Vibration due to improper mounting, etc. Mount the pump on a level surface and secure the pump to the equipment pad. 3. Foreign matter in the pump housing. Loose stones/debris hitting the impeller could be the cause. Clean the pump housing. 4. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage, which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. All seal leaks should be replaced at once. • Interference With Home Automation/Power Line Communication Equipment: 1. Make sure the terminal board connections agree with the wiring diagram on the pump data plate label. 2. Check for and correct any improper or loose wiring connections. 3. Install noise filter (from home automation/power line communication equipment vendor) to prevent equipment interference. 25 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
25
5.
Suction side clogged. Contact a qualified repair professional. You should have 5” - 6” of vacuum at the strainer cover (your pool dealer can
confirm this with a vacuum gauge). You may be able to check by removing the skimmer basket and holding an object over the bottom port with
the skimmer full and the pump running. If no suction is felt, check for line blockage.
a.
If the pump develops a vacuum, check for a blocked suction line or a dirty strainer basket. An air leak in the suction piping may be the cause.
b.
If the pump does not develop a vacuum and the pump has sufficient “priming water”:
i.
Re-check the strainer housing cover and all threaded connections for suction leaks. Check if all system hose clamps are tight.
ii.
Check voltage to ensure that the motor is rotating at full rpm’s.
iii.
Open the housing cover and check for clogging or obstruction in suction. Check the impeller for debris.
iv.
Remove and replace the shaft seal only if it is leaking.
Low Flow – Generally:
1.
Clogged or restricted strainer or suction line. Contact a qualified repair professional.
2.
Undersized pool piping. Correct the piping size.
3.
Plugged or restricted discharge line of filter, valve partially closed (high gauge reading). Sand filters – backwash as per manufacturer’s instruc-
tions; D.E. filters – backwash as per manufacturer’s instructions; Cartridge filters – clean or replace the cartridge.
4.
Air leak in suction (bubbles issuing from return fittings). Re-tighten the suction and discharge connections using PTFE tape. Inspect other plumb-
ing connections, and tighten as required.
5.
Plugged, restricted, or damaged impeller. Replace the impeller including a new seal assembly.
Noisy Pump:
1.
Air leak in suction piping, cavitations caused by restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted
discharge return lines. Correct the suction condition or throttle return lines, if practical. Holding your hand over the return fitting will sometimes
prove this, or by putting in a smaller eyeball fitting.
2.
Vibration due to improper mounting, etc. Mount the pump on a level surface and secure the pump to the equipment pad.
3.
Foreign matter in the pump housing. Loose stones/debris hitting the impeller could be the cause. Clean the pump housing.
4.
Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage, which will allow chlorinated water
to seep into bearings wiping out the grease causing bearing to whine. All seal leaks should be replaced at once.
Interference With Home Automation/Power Line Communication Equipment:
1.
Make sure the terminal board connections agree with the wiring diagram on the pump data plate label.
2.
Check for and correct any improper or loose wiring connections.
3.
Install noise filter (from home automation/power line communication equipment vendor) to prevent equipment interference.