HealthRider Crosstrainer 800s Elliptical Uk Manual - Page 7

Connect the Pulse Sensor Wire 71 to the Pulse Wire

Get HealthRider Crosstrainer 800s Elliptical PDF manuals and user guides View all HealthRider Crosstrainer 800s Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

8. Identify the Left Handlebar (9) and the Left Handlebar Leg (73), which are marked with stickers. 8 Insert the Left Handlebar (9) into the Left Handlebar Leg (73). Make sure that the short tube on the Left Handlebar and the hexagonal holes in the Left Handlebar Leg are on the same side. Attach the Left Handlebar with two M8 x 42mm Button Bolts (50) and two M8 Nylon Locknuts (46). Do not tighten the Button Bolts yet. Attach the Right Handlebar (not shown) to the Right Handlebar Leg (not shown) in the same way. 9 50 73 Tube 46 Hexagonal Holes 9. Insert the Pivot Axle (38) through the Upright (2). Apply a generous amount of the included grease to the Pivot Axle. Identify the Left and Right Handlebars (9, 10), which are marked with stickers. Have another person hold the Left Handlebar near the left end of the Pivot Axle (38). Insert the left Pulse Sensor Wire (71) through a Handlebar Spacer (25). Make sure that the Handlebar Spacer is oriented as shown, with the small cutout on top. Slide the Handlebar Spacer onto the short tube on the Left Handlebar. Connect the Pulse Sensor Wire (71) to the Pulse Wire Harness (80), and insert the Pulse Sensor Wire and the Pulse Wire Harness into the opening in the side of the Console Bracket (26). Next, slide the Left Handlebar (9) onto the Pivot Axle (38). Be careful to avoid pinching the wires. Assemble the Right Handlebar (10) in the same way. Place a M16 Wave Washer (87) on each end of the Pivot Axle (38). Next, tighten an M8 x 19mm Button Screw (22) with an M8 Large Washer (17) into each end of the Pivot Axle. Then, orient the two Handlebar Caps (23) as shown, and press the small tabs on the Handlebar Caps into the two Handlebar Spacers (25). Gently separate the two Upright Covers (82). Hold the Upright Covers around the Upright (2), and firmly press the Upright Covers together. 10. Identify the Left Pedal (13), which has an "L" molded into its bottom surface, and the Left Pedal Arm (14), which is marked with a sticker. Attach the Left Pedal (13) to the Left Pedal Arm (14) with two M8 x 50mm Button Screws (20). Attach the Right Pedal (not shown) in the same way. 7 9 82 9 80 25 71 17 87 22 38 Grease Tube 23 Tab 2 10 26 23 17 22 25 87 82 10 13 14 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
7
9
10
82
82
38
2
20
Grease
Tube
13
14
10
26
9.
Insert the Pivot Axle (38) through the Upright (2). Apply
a generous amount of the included grease to the Pivot
Axle.
Identify the Left and Right Handlebars (9, 10), which
are marked with stickers. Have another person hold
the Left Handlebar near the left end of the Pivot Axle
(38). Insert the left Pulse Sensor Wire (71) through a
Handlebar Spacer (25).
Make sure that the
Handlebar Spacer is oriented as shown, with the
small cutout on top.
Slide the Handlebar Spacer onto
the short tube on the Left Handlebar.
Connect the Pulse Sensor Wire (71) to the Pulse Wire
Harness (80), and insert the Pulse Sensor Wire and
the Pulse Wire Harness into the opening in the side of
the Console Bracket (26). Next, slide the Left
Handlebar (9) onto the Pivot Axle (38).
Be careful to
avoid pinching the wires.
Assemble the Right
Handlebar (10) in the same way.
Place a M16 Wave Washer (87) on each end of the
Pivot Axle (38). Next, tighten an M8 x 19mm Button
Screw (22) with an M8 Large Washer (17) into each
end of the Pivot Axle. Then, orient the two Handlebar
Caps (23) as shown, and press the small tabs on the
Handlebar Caps into the two Handlebar Spacers (25).
Gently separate the two Upright Covers (82). Hold the
Upright Covers around the Upright (2), and firmly
press the Upright Covers together.
10. Identify the Left Pedal (13), which has an “L” molded
into its bottom surface, and the Left Pedal Arm (14),
which is marked with a sticker.
Attach the Left Pedal (13) to the Left Pedal Arm (14)
with two M8 x 50mm Button Screws (20).
Attach the Right Pedal (not shown) in the same way.
23
23
Tab
22
22
17
87
17
25
87
71
9
80
25
8
9
73
46
Tube
Hexagonal
Holes
50
8.
Identify the Left Handlebar (9) and the Left Handlebar
Leg (73), which are marked with stickers.
Insert the Left Handlebar (9) into the Left Handlebar
Leg (73).
Make sure that the short tube on the Left
Handlebar and the hexagonal holes in the Left
Handlebar Leg are on the same side.
Attach the
Left Handlebar with two M8 x 42mm Button Bolts (50)
and two M8 Nylon Locknuts (46).
Do not tighten the
Button Bolts yet.
Attach the Right Handlebar (not shown) to the Right
Handlebar Leg (not shown) in the same way.