HealthRider H150o Treadmill English Manual - Page 7

Insert the Wire Harness 17 through the two Plastic Ties

Get HealthRider H150o Treadmill PDF manuals and user guides View all HealthRider H150o Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3. Make sure that the Right Upright (10) is turned so it bends in the direction shown. Insert two 3" Bolts (47) with two Star Washers (4) through the Base (82) and hand tighten the Bolts into the lower end of the Right Upright. With the help of a second person, tip the treadmill onto its other side and repeat steps 1 through 3. Note: There is not a wire harness on the left side. One extra Base Pad (not shown) may be included. With the help of a second person, set the treadmill flat on the floor so that the Right Upright (10) and the Left Upright (not shown) are vertical. 4. Turn the console assembly upside-down; be careful not to scratch the console assembly. Attach a Handrail (85) to the console assembly with two 1 1/2" Screws (79) as shown. Attach the other Handrail (not shown) to the other side of the console assembly in the same way. 5. Have a second person hold the console assembly near the Right Upright (10). Insert the end of the Wire Harness (17) into the bottom of the right Handrail (85) and out of the indicated hole. Using the Silver Screw (107), attach the end of the ground wire to the small hole in the side of the Handrail. 3 Bend 4 Console Assembly 5 Ground Wire Hole 82 47 10 4 85 79 107 17 10 6. Have a second person hold the Console Base (87) and the right Handrail (85) in the position shown. Touch the Right Upright (10) to discharge any static. Insert the Wire Harness (17) through the two Plastic Ties (108) on the Console Base (87). Find the 3-wire connector on the end of the Wire Harness, and insert the connector into the red socket beneath the Console Base. The connector should slide easily into the socket and snap into place. If it does not, turn the connector and then insert it. If the connectors are not inserted properly, the console may be damaged when the power is turned on. Insert the 5-wire connector into the black socket beneath the Console Base in the same way. Make sure that the connectors and wires appear as shown in the inset drawing. Insert the excess Wire Harness down through the right Handrail (85). Securely tighten the Plastic Ties (108) to prevent the Wire Harness (17) from slipping. Then, cut off the ends of the Plastic Ties. 6 87 85 10 7 85 Console Assembly 108 17 5-wire 3-wire 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
7
3.
Make sure that the Right Upright (10) is turned so it
bends in the direction shown. Insert two 3” Bolts (47) with
two Star Washers (4) through the Base (82) and
hand
tighten
the Bolts into the lower end of the Right Upright.
With the help of a second person,
tip the treadmill onto
its other side and repeat steps 1 through 3.
Note:
There is not a wire harness on the left side. One extra
Base Pad (not shown) may be included.
With the help of a second person, set the treadmill flat on
the floor so that the Right Upright (10) and the Left
Upright (not shown) are vertical.
4.
Turn the console assembly upside-down;
be careful not
to scratch the console assembly.
Attach a Handrail (85) to the console assembly with two
1 1/2” Screws (79) as shown. Attach the other Handrail
(not shown) to the other side of the console assembly in
the same way.
47
4
82
Bend
10
3
5.
Have a second person hold the console assembly near
the Right Upright (10). Insert the end of the Wire Harness
(17) into the bottom of the right Handrail (85) and out of the
indicated hole. Using the Silver Screw (107), attach the
end of the ground wire to the small hole in the side of the
Handrail.
10
85
17
107
5
Hole
Ground
Wire
6.
Have a second person hold the Console Base (87) and
the right Handrail (85) in the position shown.
Touch the
Right Upright (10) to discharge any static.
Insert the Wire Harness (17) through the two Plastic Ties
(108) on the Console Base (87). Find the 3-wire connec-
tor on the end of the Wire Harness, and insert the con-
nector into the red socket beneath the Console Base.
The connector should slide easily into the socket
and snap into place.
If it does not, turn the connector
and then insert it.
If the connectors are not inserted
properly, the console may be damaged when the
power is turned on.
Insert the 5-wire connector into the
black socket beneath the Console Base in the same way.
Make sure that the connectors and wires appear as shown
in the inset drawing. Insert the excess Wire Harness down
through the right Handrail (85).
Securely tighten the Plastic Ties (108) to prevent the
Wire Harness (17) from slipping.
Then, cut off the ends
of the Plastic Ties.
17
87
85
10
6
79
85
4
Console
Assembly
Console
Assembly
108
5-wire
17
3-wire