HP 1022n HP LaserJet 1022nw - Wireless User Guide - Page 27

Setup failed, To print a configuration Address, Networking, Wireless, Communication Mode - set ip address

Get HP 1022n - LaserJet B/W Laser Printer PDF manuals and user guides
UPC - 829160711102
View all HP 1022n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

NOTE NOTE 1. Print a configuration page. To print a configuration page, when the printer is in the Ready state, press and hold the GO button until the Ready light starts blinking. For more information, see Configuration page. 2. Enter either the URL or device IP address from the configuration page into the Address field on your Web browser. The EWS Home page appears, showing the printer device information. 3. Click the Networking tab. 4. Click the Wireless option. 5. In the Communication Mode section, select Infrastructure. 6. Select a network name (SSID) from the list of detected networks, or enter the name of a new wireless network. 7. Select WPA/PSK, enter a pass phrase (from 8 to 63 characters in length, including spaces) that will be used by the software to generate a pre-shared key. All devices on the network must use the same pass phrase. 8. Click Apply. Setup failed Possible problem: No signal is being received by the device because it is not in range of the access point (infrastructure) or computer (ad-hoc). Move the printer and the computer closer together. If the distance between your computer and the printer is significant, try reducing the distance. If possible, provide a clear path between the computer and print server, and minimize sources of radio interference. Possible problem: The setup program tried to change the computer's wireless configuration so that it can communicate to the printer, but was unable to reprogram the settings on the computer's wireless access card. 1. Quit all applications. 2. If your computer is connected to the Internet, disable the connection to your computer by removing the Ethernet cable that connects the modem (cable, DSL, or dial-up) to your computer. 3. Click Setup. The Setup menu appears. 4. Select 6. The Network menu appears. 5. Select 2. The wireless radio setting options appear. The default setting for the wireless radio is Off. 6. Use the up and down buttons to select On. 7. Select OK. 8. Open the configuration utility for your wireless network adapter. 9. Write down the existing wireless profile settings. ENWW Solving problems that occur during installation 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
1.
Print a configuration page.
To print a configuration page
, when the printer is in the
Ready state, press and hold the
G
O
button until the Ready light starts blinking. For more
information, see
Configuration
page
.
2.
Enter either the URL or device IP address from the configuration page into the
Address
field on your Web browser. The EWS Home page appears, showing the printer device
information.
3.
Click the
Networking
tab.
4.
Click the
Wireless
option.
5.
In the
Communication Mode
section, select
Infrastructure
.
6.
Select a network name (SSID) from the list of detected networks, or enter the name of a
new wireless network.
7.
Select
WPA/PSK
, enter a pass phrase (from 8 to 63 characters in length, including
spaces) that will be used by the software to generate a pre-shared key.
NOTE
All devices on the network must use the same pass phrase.
8.
Click
Apply
.
Setup failed
Possible problem:
No signal is being received by the device because it is not in range of
the access point (infrastructure) or computer (ad-hoc).
Move the printer and the computer closer together. If the distance between your computer
and the printer is significant, try reducing the distance. If possible, provide a clear path
between the computer and print server, and minimize sources of radio interference.
Possible problem:
The setup program tried to change the computer’s wireless configuration
so that it can communicate to the printer, but was unable to reprogram the settings on the
computer’s wireless access card.
1.
Quit all applications.
2.
If your computer is connected to the Internet, disable the connection to your computer by
removing the Ethernet cable that connects the modem (cable, DSL, or dial-up) to your
computer.
3.
Click
Setup
. The
Setup
menu appears.
4.
Select
6
. The
Network
menu appears.
5.
Select
2
. The wireless radio setting options appear.
NOTE
The default setting for the wireless radio is
Off
.
6.
Use the up and down buttons to select
On
.
7.
Select
OK
.
8.
Open the configuration utility for your wireless network adapter.
9.
Write down the existing wireless profile settings.
ENWW
Solving problems that occur during installation
21