HP BLc3000 HP BladeSystem c-Class Enclosure Troubleshooting Guide - Page 44

Procedures: Onboard Administrator errors

Get HP BLc3000 PDF manuals and user guides View all HP BLc3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Symptom Initial step The Onboard Administrator health LED is - off on one Onboard Administrator, and Onboard Administrator health LED is green on the second Onboard Administrator. The Onboard Administrator health LED is - off on both Onboard Administrators. The Onboard Administrator LED is red. - Required steps Begin with step 2. Begin with step 1. Begin with step 2. Procedures: Onboard Administrator errors CAUTION: Some troubleshooting procedures require powering down an entire enclosure. To avoid possible data loss, always secure permission before powering down an enclosure. CAUTION: If you are using a Virtual Connect environment, some of these procedures might cause the loss of Virtual Connect credentials and the loss of communication between the Onboard Administrator and the Virtual Connect Interconnect module. Ensure the Virtual Connect configuration is backed up before proceeding with any of the following procedures. Virtual Connect configuration can be backed up by using Virtual Connect GUI or Virtual Connect Support Utility. CAUTION: To avoid data loss, do not remove an Onboard Administrator when the Insight Display shows a firmware update in progress. During this activity, the Insight Display displays the Firmware Update screen with the Lock icon and the firmware update progress bar. Step Step 1 Step 2 Onboard Administrator errors action and verification Action Verify that at least one power supply has the following normal LED status: • The power supply power LED is on. • The power supply fault LED is off. Verification If no power supply LEDs are on, then see "Power supply troubleshooting (on page 30)." If at least one power supply indicates normal LED status, then continue to the next step. Action HP BladeSystem c7000 Enclosure If the OA tray has a single Onboard Administrator installed, reseat the OA and the OA tray: 1 Remove the suspect Onboard Administrator. 2 Reseat the OA tray. 3 Install the suspect Onboard Administrator. If the OA tray has two Onboard Administrators installed, then continue to the next step. HP BladeSystem c3000 Enclosure If the OA tray has a single Onboard Administrator installed, reseat the suspect Onboard Administrator. If the OA tray has two Onboard Administrators installed, then continue to step 6. Enclosure troubleshooting 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Enclosure troubleshooting 44
Symptom
Initial step
Required steps
The Onboard Administrator health LED is
off on one Onboard Administrator, and
Onboard Administrator health LED is
green on the second Onboard
Administrator.
—
Begin with step 2.
The Onboard Administrator health LED is
off on both Onboard Administrators.
—
Begin with step 1.
The Onboard Administrator LED is red.
—
Begin with step 2.
Procedures: Onboard Administrator errors
CAUTION:
Some troubleshooting procedures require powering down an entire enclosure. To
avoid possible data loss, always secure permission before powering down an enclosure.
CAUTION:
If you are using a Virtual Connect environment, some of these procedures might
cause the loss of Virtual Connect credentials and the loss of communication between the Onboard
Administrator and the Virtual Connect Interconnect module. Ensure the Virtual Connect
configuration is backed up before proceeding with any of the following procedures. Virtual
Connect configuration can be backed up by using Virtual Connect GUI or Virtual Connect
Support Utility.
CAUTION:
To avoid data loss, do not remove an Onboard Administrator when the Insight
Display shows a firmware update in progress. During this activity, the Insight Display displays the
Firmware Update screen with the Lock icon and the firmware update progress bar.
Step
Onboard Administrator errors action and verification
Step 1
Action
Verify that at least one power supply has the following normal LED status:
•
The power supply power LED is on.
•
The power supply fault LED is off.
Verification
If no power supply LEDs are on, then see "Power supply troubleshooting (on page
30
)."
If at least one power supply indicates normal LED status, then continue to the next step.
Step 2
Action
HP BladeSystem c7000 Enclosure
If the OA tray has a single Onboard Administrator installed, reseat the OA and the OA
tray:
1
Remove the suspect Onboard Administrator.
2
Reseat the OA tray.
3
Install the suspect Onboard Administrator.
If the OA tray has two Onboard Administrators installed, then continue to the next step.
HP BladeSystem c3000 Enclosure
If the OA tray has a single Onboard Administrator installed, reseat the suspect Onboard
Administrator.
If the OA tray has two Onboard Administrators installed, then continue to step 6.