HP D2D100 HP StorageWorks D2D Backup System User Guide (EH880-90950, October 2 - Page 40

Run the Installation wizard, Powering on the HP D2D Backup System

Get HP D2D100 PDF manuals and user guides View all HP D2D100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

1. LEDs 2. Power On button Figure 25 Powering on the HP D2D Backup System Run the Installation wizard The HP D2D Backup System can be used to back up a maximum of six hosts. You should run the Installation wizard on each host that will provide a source of data for backup. The host may be a server, workstation or PC. 1. Insert the CD-ROM supplied with your HP D2D Backup System into the host machine. It should launch automatically. If it does not, locate the D2DInstallationWizard.exe file and run it manually. 2. Select Start the wizard and follow the onscreen instructions to step through the installation, normally by pressing Next. The Installation wizard will automatically configure all the software components required for setup and use of the HP D2D Backup System. There are three main phases: • Install the tape drivers: These allow your system to recognize the tape drives created on the HP D2D Backup System. 40 The Installation wizard

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
1. LEDs
2. Power On button
Figure 25 Powering on the HP D2D Backup System
Run the Installation wizard
The HP D2D Backup System can be used to back up a maximum of six hosts. You should run the
Installation wizard on each host that will provide a source of data for backup. The host may be a
server, workstation or PC.
1.
Insert the CD-ROM supplied with your HP D2D Backup System into the host machine. It should launch
automatically. If it does not, locate the
D2DInstallationWizard.exe
fi
le and run it manually.
2.
Select
Start the wizard
and follow the onscreen instructions to step through the installation, normally
by pressing
Next
.
The Installation wizard will automatically con
fi
gure all the software components required for setup
and use of the HP D2D Backup System. There are three main phases:
•
Install the tape drivers:
These allow your system to recognize the tape drives created on the
HP D2D Backup System.
40
The Installation wizard