HP ENVY m6-ae100 ENVY Notebook PC Maintenance and Service Guide - Page 64

Remove the hard drive bracket, that secure the hard drive cover to the hard drive.

Get HP ENVY m6-ae100 PDF manuals and user guides View all HP ENVY m6-ae100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

3. Lift up on the hard drive tab (3) to remove the hard drive assembly from the hard drive bay. 4. If it is necessary to disassemble the hard drive, perform the following steps: a. Disconnect the hard drive connector cable (1) from the hard drive. b. Remove the four Phillips PM2.5×3.0 screws (2) that secure the hard drive cover to the hard drive. c. Remove the hard drive bracket (3) from the hard drive. The hard drive bracket and screws are available in the Hard Drive Hardware Kit, spare part number 812686-001. The hard drive connector cable is available using spare part number 812697-001. Reverse this procedure to install the RTC battery. 56 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
3.
Lift up on the hard drive tab
(3)
to remove the hard drive assembly from the hard drive bay.
4.
If it is necessary to disassemble the hard drive, perform the following steps:
a.
Disconnect the hard drive connector cable
(1)
from the hard drive.
b.
Remove the four Phillips PM2.5×3.0 screws
(2)
that secure the hard drive cover to the hard drive.
c.
Remove the hard drive bracket
(3)
from the hard drive.
The hard drive bracket and screws are available in the Hard Drive Hardware Kit, spare part number
812686-001. The hard drive connector cable is available using spare part number 812697-001.
Reverse this procedure to install the RTC battery.
56
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts