HP ENVY m6-ar000 Maintenance and Service Guide - Page 46

Solid-state drive, Remove the solid-state drive

Get HP ENVY m6-ar000 PDF manuals and user guides View all HP ENVY m6-ar000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Solid-state drive Description 256-MB, M2.2280, solid-state drive supporting TLC for use on all computer models 128-MB, M2.2280, SATA-3, solid-state drive for use only on computer models with model number m6aq1XX Spare part number 847109-003 827560-009 Before removing the solid-state drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 27). 5. Disconnect the battery cable from the system board (see Battery on page 29). Remove the solid-state drive: 1. Remove the Phillips PM2.0×3.8 screw (1) that secures the solid-state drive to the computer. (The solid- state drive tilts up.) 2. Remove the solid-state drive (2) by pulling the drive away from the slot at an angle. Reverse this procedure to install the solid-state drive. 38 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Solid-state drive
Description
Spare part number
256-MB, M2.2280, solid-state drive supporting TLC for use on all computer models
847109-003
128-MB, M2.2280, SATA-3, solid-state drive for use only on computer models with model number m6-
aq1XX
827560-009
Before removing the solid-state drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
27
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
29
).
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×3.8 screw
(1)
that secures the solid-state drive to the computer. (The solid-
state drive tilts up.)
2.
Remove the solid-state drive
(2)
by pulling the drive away from the slot at an angle.
Reverse this procedure to install the solid-state drive.
38
Chapter 5
Removal and replacement procedures