HP ENVY m7-n000 Maintenance and Service Guide 1 - Page 60

Display assembly

Get HP ENVY m7-n000 PDF manuals and user guides View all HP ENVY m7-n000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

2. Lift the door up to remove it (2). Reverse this procedure to install the RJ-45 door. Display assembly To remove and disassemble the display assembly, use these procedures and illustrations. Full hinge-up displays are not available as spare parts. Spare parts for displays are available only at the subcomponent level. Before removing the display panel, follow these steps: NOTE: Make sure the display assembly panel has been separated from the base enclosure. (See Display assembly panel on page 43). 1. Prepare the computer for disassembly (see Preparation for disassembly on page 33). 2. Remove the bottom cover (see Bottom cover on page 33). 3. Remove the battery (see Battery on page 34). 4. Remove the heat sink (see Heat sink on page 40). 5. Remove the fans (see Fan assembly on page 41). 6. Remove the display assembly panel (see Display assembly panel on page 43). 1. If you need to remove the display panel: IMPORTANT: After replacing the display panel assembly or the system board, it is necessary to run the service tool to have the new ambient light sensor (ALS) data written to the system BIOS. Please search for the related advisory for more information. IMPORTANT: After replacing the display panel assembly, it is necessary to reload the calibration data. Refer to Service Advisory c06640672 for details on reloading the HP Display Control Panel Color Calibration Data Reload Process. Display assembly 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
2.
Lift the door up to remove it
(2)
.
Reverse this procedure to install the RJ-45 door.
Display assembly
To remove and disassemble the display assembly, use these procedures and illustrations.
Full hinge-up displays are not available as spare parts. Spare parts for displays are available only at the
subcomponent level.
Before removing the display panel, follow these steps:
NOTE:
Make sure the display assembly panel has been separated from the base enclosure. (See
Display
assembly panel
on page
43
).
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
33
).
2.
Remove the bottom cover (see
Bottom cover
on page
33
).
3.
Remove the battery (see
Battery
on page
34
).
4.
Remove the heat sink (see
Heat sink
on page
40
).
5.
Remove the fans (see
Fan assembly
on page
41
).
6.
Remove the display assembly panel (see
Display assembly panel
on page
43
).
1.
If you need to remove the display panel:
IMPORTANT:
After replacing the display panel assembly or the system board, it is necessary to run the
service tool to have the new ambient light sensor (ALS) data written to the system BIOS. Please search
for the related advisory for more information.
IMPORTANT:
After replacing the display panel assembly, it is necessary to reload the calibration data.
Refer to Service Advisory c06640672 for details on reloading the HP Display Control Panel Color
Calibration Data Reload Process.
Display assembly
53