HP G42-232NR Compaq Presario CQ42 Notebook PC and HP G42 Notebook PC - Mainten - Page 69

Remove the Phillips PM2.0×3.0 screw

Get HP G42-232NR PDF manuals and user guides View all HP G42-232NR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

2. Loosen the 2 Phillips PM2.5×5.0 captive screws (1) that secure the mini-card compartment cover. 3. Lift the cover off the computer (2). The mini-card compartment cover is included in the plastics kit, spare part number 600190-001. 4. Disconnect the two WLAN antenna cables (1) from the WLAN module. 5. Remove the Phillips PM2.0×3.0 screw (2) that secures the WLAN module to the computer. (The edge of the module opposite the slot rises away from the computer.) 6. Remove the WLAN module (3) by pulling it away from the slot at an angle. CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support. NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion into the WLAN module slot. Reverse this procedure to install a WLAN module. ENWW Component replacement procedures 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
2.
Loosen the 2 Phillips PM2.5×5.0 captive screws
(1)
that secure the mini-card compartment
cover.
3.
Lift the cover off the computer
(2)
. The mini-card compartment cover is included in the plastics
kit, spare part number 600190-001.
4.
Disconnect the two WLAN antenna cables
(1)
from the WLAN module.
5.
Remove the Phillips PM2.0×3.0 screw
(2)
that secures the WLAN module to the computer. (The
edge of the module opposite the slot rises away from the computer.)
6.
Remove the WLAN module
(3)
by pulling it away from the slot at an angle.
CAUTION:
To prevent an unresponsive system, replace the wireless module only with a
wireless module authorized for use in the computer by the governmental agency that regulates
wireless devices in your country or region. If you replace the module and then receive a warning
message, remove the module to restore computer functionality, and then contact technical
support through Help and Support.
NOTE:
WLAN modules are designed with a notch
(4)
to prevent incorrect insertion into the
WLAN module slot.
Reverse this procedure to install a WLAN module.
ENWW
Component replacement procedures
59