HP Kayak XW A2-U2-W2 HP Kayak XW (Series U2-W2), User's Guide - Page 83

If You Can't Start the, Program, If the Date and Time Are Incorrect

Get HP Kayak XW A2-U2-W2 PDF manuals and user guides View all HP Kayak XW A2-U2-W2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

3 Troubleshooting Your PC Workstation If Your PC Workstation Has a Software Problem If You Can't Start the Setup Program This may happen if the copy of the PC Workstation's configuration stored in memory is corrupted. You will need to erase this bad configuration. To clear the configuration: 1 Switch off the PC Workstation and remove the cover ( see refer to "Removing the Cover" on page 23). 2 Set the system board switch 6 (CONFG) on the switch block DOWN to clear the configuration (refer to page page 90 for the switch location). 3 Replace the cover and switch on the PC Workstation to erase the memory. 4 Check that error codes 0240 and 0130 are displayed, and wait until the PC Workstation has started. 5 Switch off the PC Workstation and remove the cover. 6 Set the system board switch 6 (CONFG) on the switch block to OFF to re-enable the configuration. 7 Replace the cover (see refer to "Replacing the Cover" on page 25). 8 Switch on the PC Workstation and run Setup by pressing when Setup appears. (Error code 0130 will appear when the PC Workstation starts.) 9 Press to save the configuration and exit from Setup. If the Date and Time Are Incorrect The date and time can be incorrect for the following reasons: • The time has changed to reflect the beginning or end of Summer Time • The PC Workstation has been unplugged from the mains for too long and the battery is discharged. The on-board battery automatically recharges itself as soon as the PC Workstation is plugged into a power outlet. English 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
English
69
3
Troubleshooting Your PC Workstation
If Your PC Workstation Has a Software Problem
If You Can’t Start the
Setup
Program
This may happen if the copy of the PC Workstation’s configuration
stored in memory is corrupted. You will need to erase this bad
configuration.
To clear the configuration:
1
Switch off the PC Workstation and remove the cover ( see refer to
“Removing the Cover” on page 23).
2
Set the system board switch 6 (CONFG) on the switch block DOWN
to clear the configuration (refer to page page 90 for the switch
location).
3
Replace the cover and switch on the PC Workstation to erase the
memory.
4
Check that error codes
0240
and
0130
are displayed, and wait until
the PC Workstation has started.
5
Switch off the PC Workstation and remove the cover.
6
Set the system board switch 6 (CONFG) on the switch block to OFF
to re-enable the configuration.
7
Replace the cover (see refer to “Replacing the Cover” on page 25).
8
Switch on the PC Workstation and run
Setup
by pressing
when
Setup
appears. (Error code
0130
will appear when the
PC Workstation starts.)
9
Press
to save the configuration and exit from
Setup
.
If the Date and Time Are Incorrect
The date and time can be incorrect for the following reasons:
•
The time has changed to reflect the beginning or end of Summer
Time
•
The PC Workstation has been unplugged from the mains for too long
and the battery is discharged.
The on-board battery automatically recharges itself as soon as the
PC Workstation is plugged into a power outlet.