HP LH4r HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 1
defines the supported HP NetServer LP2000r configurations using the HP Rack Storage/12FC and Microsoft® Cluster Server. These configurations minimize single points of failure (SPOF, SPOFless1) and provide extended availability. The specific configuration certified and supported by both Hewlett - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 2
.SYS, version 2.66 or later. For NetRAID-xM, use MRAID2K.SYS version 5.20 (Navigator L.20.00 or later) SPU internal drive bays or HP external drive cabinet (e.g., HP Rack Storage/12), any number. Must be HP (hot swap or fixed). Any HP cables that meet SCSI specifications and any SCSI bus speed. Any - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 3
fixed) Any HP drive supported by storage enclosure Optical (Server to Hub HP D6976A 6-port fibre channel Or HP P4459A 8-port switch 1 for SPOF 2 for SPOFless with hubs HP Rack Storage/12 Number of cabinets: Model Status SCSI ID Disk SCSI IDs Disk drives: Cables LANs LAN connection Optional 1 - 2 HP - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 4
of NICs may not be used for client communication. Embedded Hptxnt5.sys 4.02.27 or later 1 Any that is on both the HP Tested Products List and the Microsoft® Hardware Compatibility List. Vendor supported driver. 1 minimum For SPOFless, 2 NICs configured as a fault-tolerant team are recommended. 4 - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 5
slots as follows: NetRAID-1M in P1 D8602B in P2 D5013B in P3 2. The bottom two shared storage devices are SCSI HP Rack Storage/12s and are optional to the cluster configuration. LEGEND Heavy (blue) lines are fibre channel Optical or Copper cables. See cabling in this guide for specifications. Dashed - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 6
Power Cabling to Separate Power Circuits (For SPOFless with 2 hubs, connect second hub to PDU that first hub is not attached to) 6 - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 7
as follows: NetRAID-1M in P1 HBA in slot P2 D5013B in P3 2. The bottom two shared storage devices are SCSI HP Rack Storage/12's and are optional to the cluster configuration. LEGEND Heavy (blue) lines are fibre channel optical or copper cables. See inside this guide for specifications. Solid red - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 8
follows NetRAID-1M in P1 HBA in P2 D5013B in P3 2. The bottom two shared storage devices are SCSI HP Rack Storage/12's and are optional to the cluster configuration. LEGEND Solid red lines are copper fibre channel. Dashed(green) lines are offset SCSI cables. See inside this guide for specifications - HP LH4r | HP Netserver LP 2000r FC Config Guide for Windows 2000 Advanced Serve - Page 9
Versions 21 March 2001 Initial release 9
1
HP NetServer LP2000r
with
HP Rack Storage/12FC
Windows
2000 Advanced Server
Cluster Configuration Guide
21 March 2001
(see
Versions
at the end of this document)
Introduction
This document defines the supported HP NetServer LP2000r configurations using the HP Rack Storage/12FC
and Microsoft
Cluster Server. These configurations minimize single points of failure (SPOF, SPOFless
1
) and
provide extended availability.
The specific configuration certified and supported by both Hewlett-Packard and
Microsoft
is defined, as are other guidelines to assist you in configuring your clustered NetServers.
This
guide is prescriptive; it describes the configurations supported by HP.
Any deviance to these configurations can
result in an inoperative cluster or an operating cluster with degraded performance, hidden SPOFs, etc., and
therefore will not be supported by HP.
What's Defined in a Racked Cluster
•
Cluster
•
SPUs
•
Local and Shared Storage
•
Intra-cluster and Client LANs
•
Shared Storage Cabling
Cluster
Type of SPUs
HP NetServer LP2000r
Each node must be the same SPU, but may have different clock speeds,
main memory sizes, cache sizes, and number of CPUs .
Number of nodes
2
Shared Storage
HP Rack Storage/12FC with 2 FCArray Cards, HP disks, and using an
HP D8602B HBA in each server.
See
Shared Storage
below.
LANs:
Client LAN
Any NIC that is HP and Microsoft
approved.
See
Client LAN
below.
For a SPOFless cluster, two D5013B NICs configured with AFT is
recommended (Add one NIC and pair with embedded).
1
For more information about configuring a SPOFless cluster, refer to the HP white paper,
High Availability
MSCS Cluster Solution
on the HP NetServers, HA Planning website.