HP Latex R2000 Introductory Information - Page 7

English

Get HP Latex R2000 PDF manuals and user guides View all HP Latex R2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

English WARNING! Take care when loading or collecting substrate, and never put your hands below the alignment bar, drying beam, or curing modules after giving the command to print. Those parts may move and adjust automatically and can cause you serious injuries. ● Before mounting the alignment bar extenders, ensure that the alignment bar is well positioned at its highest position and is not moving at all. There is a risk of trapping your fingers in the gaps. ● For the roll printing kit accessory: Take care when using the air gun. When used for cleaning purposes, make sure to use it according to local regulations: additional safety provisions may apply. ● Ensure that the tables are properly latched to the printer before using them. Before unlatching the table always clear it, remove and store both drop-in rollers in position before folding the table. Light radiation hazard UV radiation can be emitted from the LED array in compliance with the requirements of the exempt group of IEC 62471:2006: Photobiological safety of lamps and lamp systems. Optical barriers are used to determine the presence. However, you are recommended not to look directly for a long time at the output LEDs while they are on. Sound pressure level The sound pressure level could exceed 70 dBA in some print modes. Hearing protection may be required. Chemical hazard Safety data sheets identify ink ingredient and ventilation requirements to ensure any airborne exposure is adequately controlled. Current printer ink systems material safety data sheets are available at: http://www.hp.com/go/msds. Air conditioning and ventilation should meet local environmental and health and safety (EHS) guidelines and regulations. For more detailed information, see the "Ventilation and air conditioning" section included in the site preparation guide, available at: http://www.hp.com/go/latexR1000/manuals and http://www.hp.com/go/ latexR2000/manuals. Heavy substrate hazard Special care must be taken to avoid personal injury when handling heavy substrates. ● Handling heavy substrate rolls always requires two people. Care must be taken to avoid back strain and/or injury. ● Always use a forklift, pallet truck, or other handling equipment to lift substrates. The printer has been designed to be compatible with many of these devices. ● Always wear personal protective equipment including boots and gloves. Ink handling and condensates HP recommends that you wear gloves when handling ink system components and condensates. Ventilation and air conditioning As with all equipment installations, to maintain ambient comfort levels, air conditioning and ventilation in the work area should take into account that the printer produces heat. Air conditioning and ventilation should meet local environmental, health, and safety (EHS) guidelines and regulations. For a more prescriptive approach to adequate ventilation, refer to the ANSI/ASHRAE (American Society of Heating, Refrigerating, and Air-Conditioning Engineers) 62.1-2013: Ventilation for Acceptable Indoor Air Quality. An example minimum exhaust rate of 2.5 L/s.m² (0.5 cfm/ft²) of fresh air for "copy, printing rooms" is specified. NOTE: The ventilation and air conditioning units should not blow air directly onto the printer. ENWW Safety precautions 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
WARNING!
Take care when loading or collecting substrate, and never put your hands below the alignment
bar, drying beam, or curing modules after giving the command to print. Those parts may move and adjust
automatically and can cause you serious injuries.
●
Before mounting the alignment bar extenders, ensure that the alignment bar is well positioned at its highest
position and is not moving at all. There is a risk of trapping your
fi
ngers in the gaps.
●
For the roll printing kit accessory: Take care when using the air gun. When used for cleaning purposes, make
sure to use it according to local regulations: additional safety provisions may apply.
●
Ensure that the tables are properly latched to the printer before using them. Before unlatching the table
always clear it, remove and store both drop-in rollers in position before folding the table.
Light radiation hazard
UV radiation can be emitted from the LED array in compliance with the requirements of the exempt group of IEC
62471:2006:
Photobiological safety of lamps and lamp systems
. Optical barriers are used to determine the
presence. However, you are recommended not to look directly for a long time at the output LEDs while they are on.
Sound pressure level
The sound pressure level could exceed 70 dBA in some print modes. Hearing protection may be required.
Chemical hazard
Safety data sheets identify ink ingredient and ventilation requirements to ensure any airborne exposure is
adequately controlled.
Current printer ink systems material safety data sheets are available at:
go/msds
.
Air conditioning and ventilation should meet local environmental and health and safety (EHS) guidelines and
regulations. For more detailed information, see the “Ventilation and air conditioning” section included in the site
preparation guide, available at:
go/latexR1000/manuals
and
go/
latexR2000/manuals
.
Heavy substrate hazard
Special care must be taken to avoid personal injury when handling heavy substrates.
●
Handling heavy substrate rolls always requires two people. Care must be taken to avoid back strain and/or
injury.
●
Always use a forklift, pallet truck, or other handling equipment to lift substrates. The printer has been
designed to be compatible with many of these devices.
●
Always wear personal protective equipment including boots and gloves.
Ink handling and condensates
HP recommends that you wear gloves when handling ink system components and condensates.
Ventilation and air conditioning
As with all equipment installations, to maintain ambient comfort levels, air conditioning and ventilation in the work
area should take into account that the printer produces heat.
Air conditioning and ventilation should meet local environmental, health, and safety (EHS) guidelines and
regulations.
For a more prescriptive approach to adequate ventilation, refer to the ANSI/ASHRAE (American Society of Heating,
Refrigerating, and Air-Conditioning Engineers) 62.1-2013:
Ventilation for Acceptable Indoor Air Quality
. An example
minimum exhaust rate of 2.5 L/s.m² (0.5 cfm/ft²) of fresh air for “copy, printing rooms” is speci
fi
ed.
NOTE:
The ventilation and air conditioning units should not blow air directly onto the printer.
ENWW
Safety precautions
5
English