HP ML310 HP Factory-Installed Operating System Software for Microsoft Windows - Page 21

Installing the Network Teaming and Configuration Utility, Using HP Software Update Manager (HPSUM),

Get HP ML310 - ProLiant - G2 PDF manuals and user guides View all HP ML310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Installing the Network Teaming and Configuration Utility The CPQTEAM Utility enables multiple NICs to be teamed together. You must run the HP Software update manager to install the CPQTEAM utility. During the CPQTEAM software installation process, a message might appear, stating that the CPQTEAM.DLL file is needed. A default path appears in the message box. Click OK to accept the path and continue with the installation. Using HP Software Update Manager (HPSUM) HPSUM is installed when the server software is installed. This software contains device drivers and utilities that take advantage of specific capabilities offered with ProLiant server products. These drivers are provided for use with ProLiant hardware only. For more information, see the PSP for the operating system located on the disk drive in the C:\hpsum directory. To launch HPSUM: 1. Click Start, and then select All Programs>Pre-Install Features>ProLiant Support Pack. 2. Follow the on-screen instructions when the setup program is launched. To manually launch the setup program: 1. Click Start>Run. 2. Enter the following path in the textbox: C:\HPSUM\SETUPEX.EXE 3. Click OK. 4. After the setup program is launched, follow the on-screen instructions. Configuring array controllers If an array controller has been purchased with the server, run the online ACU to set up the remaining physical drives for use. IMPORTANT: Microsoft® Internet Explorer is required to run the ACU. Internet Explorer is used to interface with the array controller. For the page to display properly, the server IP address must be included in the trusted sites list. Internet Explorer must be restarted after adding the IP address to the trusted sites list for the settings to take effect. 1. Click Start, and select All Programs>HP System Tools>HP Array Configuration Utility. 2. Select whether you want to enable remote administration when prompted. 3. Click OK. 4. When prompted for the Web-Based Management password, enter the credentials for either the local administrator account or a local user account in the following format: domain name\login name 5. Configure the remaining physical drives into logical drives, and run Disk Administrator to partition and format the additional drive space. Post-installation tasks for HP ProLiant 300 series servers only 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
Post-installation tasks for HP ProLiant 300 series servers only
21
Installing the Network Teaming and Configuration
Utility
The CPQTEAM Utility enables multiple NICs to be teamed together. You must run the HP Software update
manager to install the CPQTEAM utility.
During the CPQTEAM software installation process, a message might appear, stating that the
CPQTEAM.DLL file is needed. A default path appears in the message box. Click
OK
to accept the path
and continue with the installation.
Using HP Software Update Manager (HPSUM)
HPSUM is installed when the server software is installed. This software contains device drivers and utilities
that take advantage of specific capabilities offered with ProLiant server products. These drivers are
provided for use with ProLiant hardware only. For more information, see the PSP for the operating system
located on the disk drive in the C:\hpsum directory.
To launch HPSUM:
1.
Click
Start
, and then select
All Programs>Pre-Install Features>ProLiant Support Pack
.
2.
Follow the on-screen instructions when the setup program is launched.
To manually launch the setup program:
1.
Click
Start>Run
.
2.
Enter the following path in the textbox:
C:\HPSUM\SETUPEX.EXE
3.
Click
OK
.
4.
After the setup program is launched, follow the on-screen instructions.
Configuring array controllers
If an array controller has been purchased with the server, run the online ACU to set up the remaining
physical drives for use.
IMPORTANT:
Microsoft® Internet Explorer is required to run the ACU. Internet Explorer is used
to interface with the array controller. For the page to display properly, the server IP address
must be included in the trusted sites list. Internet Explorer must be restarted after adding the IP
address to the trusted sites list for the settings to take effect.
1.
Click
Start,
and select
All Programs>HP System Tools>HP Array Configuration Utility.
2.
Select whether you want to enable remote administration when prompted.
3.
Click
OK.
4.
When prompted for the Web-Based Management password, enter the credentials for either the local
administrator account or a local user account in the following format:
domain name\login name
5.
Configure the remaining physical drives into logical drives, and run Disk Administrator to partition
and format the additional drive space.