HP OmniBook 3100 HP OmniBook 3100 - Memory Installation Sheet - Page 1
HP OmniBook 3100 - Notebook PC Manual
View all HP OmniBook 3100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
RAM Expansion Module Caution: Static electricity can permanently damage computer chips. To avoid damaging your RAM expansion module: • Discharge your body's electricty by touching the metal shielding around the connectors on the rear of the OmniBook computer. • Handle the RAM expansion module only by its edges. To install the RAM expansion module You will need a small Phillips screwdriver to install the RAM expansion module. 1 From the Start menu, shut down the OmniBook. 2 Unplug the ac adapter, if present, and remove all batteries. 3 Remove the two screws from the bottom of the hard disk drive and pull out the drive as shown. 4 Slide open the RAM cover about 3 mm, then lift off the cover. RAM-Erweiterungsmodul Achtung: Durch statische Elektrizität können Computer-Chips beschädigt werden. Beachten Sie daher folgende Hinweise, damit die RAM-Erweiterungsmodule nicht beschädigt werden: • Berühren Sie die Metallblenden an den Anschlüssen an der Rückseite des OmniBook Rechners, um körpereigene Spannung abzuleiten. • Fassen Sie das RAM-Erweiterungsmodul nur an den Kanten an. Einsetzen des RAM-Erweiterungsmoduls Für den Einbau des RAM-Erweiterungsmoduls benötigen Sie einen Schlitzschraubendreher. 1 Fahren Sie den OmniBook Rechner über das Menü Start herunter. 2 Ziehen Sie ggf. den Netzadapter ab, und entfernen Sie alle Akkus. 3 Lösen Sie die beiden Schrauben unten am Festplattenlaufwerk, und nehmen Sie das Laufwerk wie dargestellt heraus. 4 Schieben Sie die RAM-Abdeckung ca. 3 mm auf, und heben Sie die Abdeckung ab. 5 Insert the RAM expansion module into the connector at about a 30 ° angle until it's fully inserted. Then press down at both sides of the module until it latches. 6 Place the RAM cover about 3mm from its closed position, then slide it closed. 7 Insert the hard drive and install the two screws. 8 Insert the battery. To remove the RAM expansion module After you remove the battery and open the RAM cover, do the following: 1 Release the two metal latches at the sides of the RAM expansion module by pushing them outward (away from the sides of the module). When you release the latches, the free edge of the module pops up. 2 Pull the module out of the connector. See the printed Reference Guide provided with your OmniBook for more information about replacing a RAM expansion module. RAM Expansion Module Multilingual Printed in U.S.A. 1 2 3 4 5 6 7 8 9 10 11 12 94 95 96 97 98 99 ® Part Number (P) 5965-0273 Edition 2 5 Führen Sie das RAM-Erweiterungsmodul vollständig in einem Winkel von ca. 30 ° ein. Drücken Sie dann das Modul an beiden Seiten herunter, bis es fest sitzt. 6 Setzen Sie die RAM-Abdeckung im Abstand von ca. 3 mm von der Schließposition wieder an. Schließen Sie danach das Fach. 7 Setzen Sie das Festplattenlaufwerk ein, und bringen Sie die Schrauben wieder an. 8 Setzen Sie die Akkus wieder ein. Herausnehmen des RAM-Erweiterungsmoduls Nehmen Sie zunächst den Akku heraus, und entfernen Sie die RAM-Abdeckung. Gehen Sie danach folgendermaßen vor: 1 Lösen Sie die beiden Metallhalteklammern an den Kanten des RAM-Erweiterungsmoduls. Drücken Sie die Klammer hierzu nach außen (von den Modulkanten weg). Wenn Sie die Klammern loslassen, springt die freie Kante des Moduls heraus. 2 Nehmen Sie das Modul aus dem Anschluß heraus. Weitere Informationen zum RAM-Erweiterungsmodul finden Sie im Referenzhandbuch, das zusammen mit dem OmniBook Rechner ausgeliefert wird. Módulo de Expansión de RAM Precaución: La electricidad estática puede dañar de forma permanente los chips del computador. Para evitar que se dañe el módulo de expansión de RAM: • Descargue la electricidad de su cuerpo tocando la protección metálica que hay alrededor de los conectores de la parte posterior del computador OmniBook. • Manipule el módulo de expansión de RAM sólo por sus extremos. Cómo instalar el módulo de expansión de RAM Para instalar el módulo de expansión de RAM necesitará un destornillador Phillips pequeño. 1 En el menú Inicio, cierre el OmniBook. 2 Desenchufe el adaptador de ca, si está enchufado, y saque todas las baterías. 3 Quite los dos tornillos de la parte inferior de la unidad de disco duro y tire de la unidad hacia fuera, tal como se muestra. 4 Abra la cubierta de la RAM deslizándola unos 3 mm y después levántela. 5 Inserte el módulo de expansión de RAM en el conector a un ángulo de unos 30 ° hasta que esté perfectamente colocado. A continuación, presione sobre ambos lados del módulo hasta que éste quede enganchado. 6 Coloque la cubierta de la RAM a unos 3 mm de su posición cerrada y después deslícela hasta que se cierre. 7 Inserte la unidad de disco duro e instale los dos tornillos. 8 Inserte la batería. Cómo sacar el módulo de expansión de RAM Después de quitar la batería y de abrir la cubierta de la RAM, haga lo siguiente: 1 Libere los dos enganches metálicos que hay a ambos lados del módulo de expansión de RAM empujándolos hacia afuera (separándolos de los lados del módulo). Al liberar los enganches, aparece el extremo libre del módulo. 2 Tire del módulo sacándolo fuera del conector. En la Guía de Consulta impresa que acompaña al OmniBook encontrará más información sobre cómo cambiar un módulo de expansión de RAM.