HP PageWide Managed Color MFP P77950 On-Site Installation Guide - Page 51

USB flash drive (control-panel menu), USB flash drive (Pre-boot menu), Enable Retrieve from USB

Get HP PageWide Managed Color MFP P77950 PDF manuals and user guides View all HP PageWide Managed Color MFP P77950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

7. Click the Download button, and then save the firmware upgrade file (compressed ZIP file). 8. Extract the firmware bundle file. After uncompressing the file, you will see a xxxxxxx.bdl file. Copy the xxxxxxx.bdl file to a portable USB flash memory storage device (thumb drive). USB Flash Drives with a CD formatted partition may not be recognized by the printer. You may need to try a different USB flash drive. USB flash drive (control-panel menu) NOTE: Staging activity will require updating the firmware in the Pre-boot menu Go to Pre-Boot walk-up firmware upgrade in the Staging chapter. NOTE: USB flash drives that are not using a FAT32 format, or do not have a CD formatted partition, might not be recognized by the printer. If the printer does not recognize a USB flash drive, try using a different USB flash drive. TIP: The USB port on the printer must be enabled. If it is disabled, use the Enable Retrieve from USB item in the General Settings menu to enable it. USB flash drive firmware (control-panel menu) upgrade from a touchscreen control panel 1. Turn the printer on, and then wait until it initializes and comes to Ready state. 2. From the Home screen on the printer control panel, swipe (right), and select Support Tools. 3. Open the following menus: ● Maintenance ● USB Firmware Upgrade 4. Insert the USB flash drive with the .bdl file on it into the USB port on the printer. 5. Select the .bdl file, and then select Install. NOTE: If there is more than one .bdl file on the storage device, make sure to select the correct file for this printer. 6. When the upgrade is complete, the printer automatically restarts. TIP: Print a configuration page and verify that the upgrade firmware version was installed. USB flash drive (Pre-boot menu) IMPORTANT: Only use this method of performing a firmware upgrade if the printer cannot initialize to the Ready state. USB flash drive firmware (Pre-boot menu) upgrade from a touchscreen control panel 1. Copy the .bdl file to a portable USB flash drive. ENWW Firmware upgrade 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
7.
Click the Download button, and then save the firmware upgrade file (compressed ZIP file).
8.
Extract the firmware bundle file. After uncompressing the file, you will see a xxxxxxx.bdl file. Copy the
xxxxxxx.bdl file to a portable USB flash memory storage device (thumb drive). USB Flash Drives with a CD
formatted partition may not be recognized by the printer. You may need to try a different USB flash drive.
USB flash drive (control-panel menu)
NOTE:
Staging activity will require updating the firmware in the Pre-boot menu Go to Pre-Boot walk-up
firmware upgrade in the Staging chapter.
NOTE:
USB flash drives that are not using a FAT32 format, or do not have a CD formatted partition, might not
be recognized by the printer. If the printer does not recognize a USB flash drive, try using a different USB flash
drive.
TIP:
The USB port on the printer must be enabled. If it is disabled, use the
Enable Retrieve from USB
item in the
General Settings
menu to enable it.
USB flash drive firmware (control-panel menu) upgrade from a touchscreen control panel
1.
Turn the printer on, and then wait until it initializes and comes to
Ready
state.
2.
From the Home screen on the printer control panel, swipe (right), and select
Support Tools
.
3.
Open the following menus:
●
Maintenance
●
USB Firmware Upgrade
4.
Insert the USB flash drive with the .bdl file on it into the USB port on the printer.
5.
Select the .bdl file, and then select
Install
.
NOTE:
If there is more than one .bdl file on the storage device, make sure to select the correct file for this
printer.
6.
When the upgrade is complete, the printer automatically restarts.
TIP:
Print a configuration page and verify that the upgrade firmware version was installed.
USB flash drive (Pre-boot menu)
IMPORTANT:
Only use this method of performing a firmware upgrade if the printer cannot initialize to the
Ready
state.
USB flash drive firmware (Pre-boot menu) upgrade from a touchscreen control panel
1.
Copy the .bdl file to a portable USB flash drive.
ENWW
Firmware upgrade
45