HP Pavilion 11-h010ca HP Pavilion 11 x2 PC Maintenance and Service Guide - Page 47

panel assembly., built into the display

Get HP Pavilion 11-h010ca PDF manuals and user guides View all HP Pavilion 11-h010ca manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Before removing the power button board, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4. Remove the display enclosure (see Display enclosure on page 30). 5. Disconnect the tablet battery cable from the system board (see Sensor board on page 31). Remove the power button board: 1. Disconnect the power button board cable (1) from the sensor board. 2. Detach the left wireless antenna transceiver (2) from the heat sink. (The wireless antenna transceiver is attached to the heat sink with double-sided tape.) 3. Release the power button board cable from the routing clips (3) built into the display panel assembly. 4. Detach the power button board (4) from the display panel assembly. (The power button board is attached to the display panel assembly with double-sided tape.) 5. Remove the power button board and cable. Reverse this procedure to install the power button board. Tablet component replacement procedures 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Before removing the power button board, follow these steps:
1.
Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.
2.
Disconnect the power from the tablet by unplugging the power cord from the tablet.
3.
Disconnect all external devices from the tablet.
4.
Remove the display enclosure (see
Display enclosure
on page
30
).
5.
Disconnect the tablet battery cable from the system board (see
Sensor board
on page
31
).
Remove the power button board:
1.
Disconnect the power button board cable
(1)
from the sensor board.
2.
Detach the left wireless antenna transceiver
(2)
from the heat sink. (The wireless antenna
transceiver is attached to the heat sink with double-sided tape.)
3.
Release the power button board cable from the routing clips
(3)
built into the display
panel assembly.
4.
Detach the power button board
(4)
from the display panel assembly. (The power button board is
attached to the display panel assembly with double-sided tape.)
5.
Remove the power button board and cable.
Reverse this procedure to install the power button board.
Tablet component replacement procedures
39