HP Pavilion 11-n000 Pavilion 11 x360 PC Maintenance and Service Guide - Page 60

The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system

Get HP Pavilion 11-n000 PDF manuals and user guides View all HP Pavilion 11-n000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Remove the heat sink: NOTE: You do not have to remove the fan to remove the heat sink. You must disengage the tape that secures the heat sink to the fan. 1. Following the 1 through 4 sequence stamped into the heat sink, remove the four Phillips PM2.0×3.0 screws (1) that secure the heat sink to the system board. 2. Detach the tape (2) that secures the heat sink to the fan. 3. Remove the heat sink (3). NOTE: Due to the adhesive quality of the thermal material located between the heat sink and the system board components, it may be necessary to move the heat sink from side to side to detach it. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board components each time the heat sink is removed. Thermal paste is used on the processor (1) and the heat sink section (2) that services it 52 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Remove the heat sink:
NOTE:
You do not have to remove the fan to remove the heat sink. You must disengage the tape that
secures the heat sink to the fan.
1.
Following the 1 through 4 sequence stamped into the heat sink, remove the four Phillips PM2.0×3.0
screws
(1)
that secure the heat sink to the system board.
2.
Detach the tape
(2)
that secures the heat sink to the fan.
3.
Remove the heat sink
(3)
.
NOTE:
Due to the adhesive quality of the thermal material located between the heat sink and the
system board components, it may be necessary to move the heat sink from side to side to detach it.
NOTE:
The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system
board components each time the heat sink is removed. Thermal paste is used on the processor
(1)
and the
heat sink section
(2)
that services it
52
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts