HP Pavilion tx1200 HP Pavilion tx1000 Entertainment PC - Maintenance and Servi - Page 75

WWAN external antenna board

Get HP Pavilion tx1200 - Notebook PC PDF manuals and user guides View all HP Pavilion tx1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

i. System board (see System board on page 66) j. Pen holder (see Pen holder on page 68). Remove the audio/infrared board: 1. Remove the two Phillips PM2.0×5.0 screws (1) that secure the audio/infrared board to the system board. 2. Release the audio/infrared board (2) by sliding it away from you until the connectors on the front of the board disengage from the openings in the base enclosure. 3. Remove the audio/infrared board (3). Reverse this procedure to install the audio/infrared board. WWAN external antenna board NOTE: The WWAN external antenna board and WWAN external antenna board cable are included with the base enclosure for use only with computer models equipped WWAN, spare part number 441136-001. Before removing the WWAN external antenna board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. 4. Remove the battery (see Battery on page 36). 5. Remove the following components: a. Hard drive (see Hard drive on page 38) b. Memory module compartment cover (see Memory module on page 43) c. Optical drive (see Optical drive on page 42) 70 Chapter 5 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
i
.
System board (see
System board
on page
66
)
j
.
Pen holder (see
Pen holder
on page
68
).
Remove the audio/infrared board:
1
.
Remove the two Phillips PM2.0×5.0 screws
(1)
that secure the audio/infrared board to the system
board.
2
.
Release the audio/infrared board
(2)
by sliding it away from you until the connectors on the front
of the board disengage from the openings in the base enclosure.
3
.
Remove the audio/infrared board
(3)
.
Reverse this procedure to install the audio/infrared board.
WWAN external antenna board
NOTE:
The WWAN external antenna board and WWAN external antenna board cable are
included with the base enclosure for use only with computer models equipped WWAN, spare part
number 441136-001.
Before removing the WWAN external antenna board, follow these steps:
1
.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2
.
Disconnect all external devices connected to the computer.
3
.
Disconnect the power cord.
4
.
Remove the battery (see
Battery
on page
36
).
5
.
Remove the following components:
a
.
Hard drive (see
Hard drive
on page
38
)
b
.
Memory module compartment cover (see
Memory module
on page
43
)
c
.
Optical drive (see
Optical drive
on page
42
)
70
Chapter
5
Removal and replacement procedures
ENWW