Home » HP Manuals » Servers » HP ProLiant BL25p » Manual Viewer

HP ProLiant BL25p HP ProLiant BL25p Generation 2 Server Blade User Guide - Page 77

Class A equipment, Declaration of conformity for products marked with the FCC logo, United States only

Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. Class B equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. Declaration of conformity for products marked with the FCC logo, United States only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding this product, contact us by mail or telephone: • Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 • 1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded or monitored.) For questions regarding this FCC declaration, contact us by mail or telephone: • Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 • 1281-514-3333 To identify this product, refer to the part, series, or model number found on the product. Regulatory compliance notices 77

Section	Page
HP ProLiant BL25p Generation 2 Server Blade User Guide	1
Notice	2
Contents	3
Component identification	6
Front panel LEDs	6
Front panel components	7
Rear panel components	8
SAS and SATA hard drive LED combinations	8
System board components	9
DIMM slot numbering	10
System maintenance switch	10
Internal USB connector	11
Local I/O cable	11
Operations	13
Power up the server blade	13
Power down the server blade	13
Remove the server blade	14
Remove the access panel	14
Setup	16
Overview	16
Installing the HP BladeSystem components	16
Verifying system components	16
Connecting to the network	17
Server blade enclosure network connections	17
Server blade enclosure compatibility	17
iLO 2 connections	17
RJ-45 patch panel Ethernet connections	17
RJ-45 patch panel 2 FC connections	18
Interconnect switch and FC connections	19
Installing server blade options	19
Installing a server blade	20
Completing the configuration	21
Hardware options installation	22
Processor option	22
Hard drive option	27
Memory option	28
DIMM guidelines	28
Installing DIMMs	29
Fibre Channel mezzanine option	29
NIC mezzanine option	30
Battery-Backed Write Cache Enabler option	31
Cabling	34
Using the local I/O cable	34
Local administration using iLO 2	34
Connecting locally to a server blade with video and USB devices	35
Accessing a server blade with local KVM	35
Accessing local media devices	36
Configuration and utilities	38
Server blade deployment tools	38
Software drivers and additional components	38
ProLiant pClass Advanced management	38
Network-based PXE deployment	39
Deployment overview	39
Deployment infrastructure	40
Static IP bay configuration	41
Deployment methods	41
PXE deployment	42
CD-ROM deployment	42
Diskette image deployment	43
SAN configuration	44
Configuration tools	45
SmartStart software	45
SmartStart Scripting Toolkit	45
HP ROM-Based Setup Utility	46
Using RBSU	46
Auto-configuration process	46
Boot options	47
BIOS Serial Console	47
Array Configuration Utility	47
Option ROM Configuration for Arrays	47
HP ProLiant Essentials Rapid Deployment Pack	48
Re-entering the server serial number and product ID	48
Management tools	48
Automatic Server Recovery	48
ROMPaq utility	49
Integrated Lights-Out 2 technology	49
HP ProLiant Essentials Integrated Lights-Out Select Pack	49
Erase Utility	49
StorageWorks library and tape tools	50
HP Systems Insight Manager	50
Management Agents	50
HP ProLiant Essentials Virtualization Management Software	50
HP ProLiant Essentials Server Migration Pack - Physical to ProLiant Edition	51
HP ProLiant Essentials Performance Management Pack	51
HP ProLiant Essentials Vulnerability and Patch Management Pack	51
HP ProLiant Essentials Workload Management Pack	52
HP BladeSystem Essentials Insight Control Data Center Edition	52
HP Control Tower	52
Redundant ROM support	52
Safety and security benefits	52
USB support	53
Internal USB functionality	53
Networking tools	53
HP ProLiant Essentials Intelligent Networking Pack	53
HP ProLiant Essentials RDMA Pack for Multifunction Gigabit server adapters	53
HP ProLiant Essentials Accelerated iSCSI Pack for Embedded Multifuncion Gigabit server adapters	54
Diagnostic tools	54
HP Insight Diagnostics	54
Survey Utility	54
Integrated Management Log	54
Array Diagnostic Utility	55
Remote support and analysis tools	55
HP Instant Support Enterprise Edition	55
Web-Based Enterprise Service	55
Open Services Event Manager	55
Keeping the system current	56
Drivers	56
Resource Paqs	56
ProLiant Support Packs	56
Operating system version support	56
System Online ROM flash component utility	56
Change control and proactive notification	57
Care Pack	57
Troubleshooting	58
Troubleshooting resources	58
Pre-diagnostic steps	58
Important safety information	59
Symbols on equipment	59
Warnings and cautions	59
Symptom information	60
Prepare the server for diagnosis	61
Service notifications	61
Loose connections	61
Troubleshooting flowcharts	62
Start diagnosis flowchart	62
General diagnosis flowchart	63
Server blade power-on problems flowchart	65
POST problems flowchart	67
OS boot problems flowchart	69
Server fault indications flowchart	71
POST error messages and beep codes	73
Introduction	73
Battery replacement	75
Regulatory compliance notices	76
Regulatory compliance identification numbers	76
Federal Communications Commission notice	76
FCC rating label	76
Class A equipment	77
Class B equipment	77
Declaration of conformity for products marked with the FCC logo, United States only	77
Modifications	78
Cables	78
Canadian notice (Avis Canadien)	78
European Union regulatory notice	78
Disposal of waste equipment by users in private households in the Eurpoean Union	79
Japanese notice	79
BSMI notice	79
Korean notice	80
Laser compliance	80
Battery replacement notice	80
Taiwan battery recycling notice	81
Power cord statement for Japan	81
Electrostatic discharge	82
Preventing electrostatic discharge	82
Grounding methods to prevent electrostatic discharge	82
Specifications	83
Environmental specifications	83
Server blade specifications	83
Technical support	84
Before you contact HP	84
HP contact information	84
Customer Self Repair	84
Acronyms and abbreviations	92

Match case Limit results 1 per page

Regulatory compliance notices 77

Class A equipment

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to correct

the interference at personal expense.

Class B equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit that is different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio or television technician for help.

Declaration of conformity for products marked with the

FCC logo, United States only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

For questions regarding this product, contact us by mail or telephone:

•

Hewlett-Packard Company

P. O. Box 692000, Mail Stop 530113

Houston, Texas 77269-2000

•

1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded

or monitored.)

For questions regarding this FCC declaration, contact us by mail or telephone:

•

Hewlett-Packard Company

P. O. Box 692000, Mail Stop 510101

Houston, Texas 77269-2000

•

281-514-3333

To identify this product, refer to the part, series, or model number found on the product.