HP Server rp2400 Hardware Manual - rp24xx, Customer Viewable - Page 82

Step 1.

Get HP Server rp2400 PDF manuals and user guides View all HP Server rp2400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Server Slide Rail Installation The following illustration shows rail parts only. Plastic parts bags, plastic end caps, and the cable management device is not shown: NOTE This illustration shows non-E-series HP cabinet columns The following procedures list the steps required to install a stand-alone server in a cabinet. Step 1. Attach rear slide mounts to the outer rails using M4 x 0.7mm screws. Do not fully tighten screws. Allow the rear slide mount to move along slot in the outer rail. 90 Chapter

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Chapter
Server Slide Rail Installation
90
The following illustration shows rail parts only. Plastic parts bags, plastic end caps, and the cable
management device is not shown:
NOTE
This illustration shows non-E-series HP cabinet columns
The following procedures list the steps required to install a stand-alone server in a cabinet.
Step 1.
Attach rear slide mounts to the outer rails using M4 x 0.7mm screws. Do not fully tighten screws.
Allow the rear slide mount to move along slot in the outer rail.