HP Spectre x2 Maintenance and Service Guide - Page 51

Remove the system board, WLAN module antenna cables

Get HP Spectre x2 PDF manuals and user guides View all HP Spectre x2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

1. Turn off the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and then shut it down through the operating system. 2. Disconnect the power from the slate by unplugging the power cord from the slate. 3. Disconnect all external devices from the slate. 4. Remove the display panel assembly (see Display panel assembly on page 20), and then remove the following components: a. Battery (see Battery on page 23) b. Solid-state drive (see Solid-state drive on page 24) c. WWAN module (see WWAN module on page 25) d. Speakers (see Speakers on page 29) e. 3D camera board (see 3D camera board on page 34) NOTE: When replacing the system board, be sure that the heat sink is removed from the defective system board and installed on the replacement system board. See Heat sink on page 43for more information. Remove the system board: 1. Disconnect the following cables from the system board: (1) WLAN module antenna cables NOTE: The WLAN "Main/#1"antenna cable is connected to the WLAN module "Main" terminal. The WLAN "Aux/#2"antenna cable is connected to the WLAN module "Aux" terminal. (2) Left microphone ZIF connector cable (3) Card reader board ZIF connector cable (4) Display panel cable (5) POGO pin docking cable Component replacement procedures 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
1.
Turn off the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and then
shut it down through the operating system.
2.
Disconnect the power from the slate by unplugging the power cord from the slate.
3.
Disconnect all external devices from the slate.
4.
Remove the display panel assembly (see
Display panel assembly
on page
20
), and then remove
the following components:
a.
Battery (see
Battery
on page
23
)
b.
Solid-state drive (see
Solid-state drive
on page
24
)
c.
WWAN module (see
WWAN module
on page
25
)
d.
Speakers (see
Speakers
on page
29
)
e.
3D camera board (see
3D camera board
on page
34
)
NOTE:
When replacing the system board, be sure that the heat sink is removed from the defective system
board and installed on the replacement system board. See
Heat sink
on page
43
for more information.
Remove the system board:
1.
Disconnect the following cables from the system board:
(1)
WLAN module antenna cables
NOTE:
The WLAN “Main/#1”antenna cable is connected to the WLAN module “Main” terminal. The
WLAN “Aux/#2”antenna cable is connected to the WLAN module “Aux” terminal.
(2)
Left microphone ZIF connector cable
(3)
Card reader board ZIF connector cable
(4)
Display panel cable
(5)
POGO pin docking cable
Component replacement procedures
41