Home » HP Manuals » Storage Devices » HP StorageWorks 8/20q » Manual Viewer

HP StorageWorks 8/20q HP StorageWorks 8/20q Fibre Channel Switch Installation - Page 24

Switch services

View all HP StorageWorks 8/20q manuals

Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

fabrics, the interoperability mode must be configured to InteropMode=0. Other B-Series or C-Series switches in the remote fabric need not support NPIV. NOTE: Be sure to configure the TR_Port before connecting the remote fabric to the HP StorageWorks 8/20q Fibre Channel Switch. If the remote fabric is connected to a port on the HP StorageWorks 8/20q Fibre Channel Switch that is not a TR_Port, the two fabrics may establish an E_Port connection and the local and remote fabrics may merge. This mixed fabric is not supported . If the port type is changed to TR_Port after connecting the remote fabric, a port reset may be required to completely establish the connection. 3. Map local devices to remote devices and activate the connection. The QuickTools mapping process creates an inter-fabric zone (IFZ) in the active zone set consisting of the local device, the remote device, and the TR_Port. When the mapping is complete, QuickTools activates the new zone set. The name of the inter-fabric zone begins with IFZ followed by the lowest device port WWN followed by the remaining port WWN, all uppercase, separated by underscores (_). For example, consider the following local and remote device WWNs: • Local device: 21:00:00:e0:8b:0e:d3:59 • Remote device: 22:00:00:04:cf:a8:7f:2d The inter-fabric zone name would be: IFZ_210000E08B0ED359_22000004CFA87F2D 4. Apply the same inter-fabric zone that was created on the local fabric to the active zoning on the remote fabric. QuickTools creates a suggested list of commands during the mapping process that, when run on a remote fabric consisting of HP StorageWorks B-Series or C-Series switches, will make the necessary zoning changes to the remote fabric. See the HP StorageWorks 8/20q Fibre Channel Switch QuickTools Switch Management User Guide for important details on creating and using this list of suggested commands.When modifications to the active zoning on both fabrics are complete, the transparent routing connection becomes active, and the local devices will discover the remote devices. Switch services You can configure your switch to suit the demands of your environment by enabling or disabling a variety of switch services. Familiarize yourself with the following switch services and determine which ones you need. • Telnet: Provides for the management of the switch over a Telnet connection. Disabling this service is not recommended. The default is enabled. • Secure Shell (SSH): Provides for secure remote connections to the switch using SSH. Your workstation must also use an SSH client. The default is disabled. • GUI Management: Provides for out-of-band management of the switch with Simple SAN Connection Manager, QuickTools, SNMP, and SMI-S. If this service is disabled, the switch can only be managed inband or through the serial port. The default is enabled. • Inband Management: Provides for the management of the switch over an inter-switch link using Simple SAN Connection Manager, QuickTools, SNMP, or management server. If you disable inband management, you can no longer communicate with that switch by means other than an Ethernet or serial connection. The default is enabled. • Secure Socket Layer (SSL): Provides for secure SSL connections for the QuickTools web applet and SMI-S. This service must be enabled to authenticate users through a Remote Authentication Dial-in Service (RADIUS) server. To enable secure SSL connections, you must first synchronize the date and time on the switch and the workstation. Enabling SSL automatically creates a security certificate on the switch. The default is disabled. NOTE: Simple SAN Connection Manager version 1.0 does not support the SSL service. If SSL is enabled, you will be unable to manage the switch using this version of Simple SAN Connection Manager. 24

Section	Page
Contents	3
About this guide	7
Intended audience	7
Related documentation	7
Document conventions and symbols	8
Table 1 Document conventions	8
Rack stability	9
HP technical support	9
Customer self repair	9
Product warranties	9
Subscription service	9
HP web sites	10
Documentation feedback	10
General description	11
Figure 1 8/20q Fibre Channel Switch	11
Switch LEDs and controls	12
Figure 2 Switch LEDs and controls	12
Input power LED (green)	12
Heartbeat LED (green)	12
System fault LED (amber)	12
Maintenance button	13
Resetting a switch	13
Placing the switch in maintenance mode	13
Fibre Channel ports	14
Figure 3 Fibre Channel ports	14
Port LEDs	14
Figure 4 Port LEDs	14
Port Logged-in LED (green)	14
Port Activity LED (green)	15
Transceivers	15
Port types	15
Table 2 Fibre Channel port types	15
Ethernet port	16
Figure 5 Ethernet port	16
Serial port	16
Figure 6 Serial port and pin identification	16
Table 3 Serial port pin identification	17
Power supply and fans	17
Switch management	17
QuickTools web applet	18
Simple SAN Connection Manager	18
Command line interface	18
Simple Network Management Protocol	18
Storage Management Initiative–Specification (SMI-S)	18
File transfer protocols	18
Planning	19
Devices	19
Device access	19
Table 4 Zoning database limits	20
Performance	20
Distance	20
Bandwidth	20
Latency	21
Table 5 Port-to-port latency	21
Feature licenses	21
Multiple switch fabrics	21
Optimizing device performance	21
Domain ID, principal priority, and domain ID lock	22
Common topologies	22
Transparent routing	23
Switch services	24
Security	26
User account security	26
IP security	26
Port binding	26
Connection security	26
Device security	27
Fabric management	28
Installation	29
Site requirements	29
Management Station and Workstation requirements	29
Table 6 Management station requirements for Simple SAN Connection Manager	29
Table 7 Workstation requirements for QuickTools	30
Switch power requirements	30
Environmental conditions	30
Installing a switch	30
Mount the switch	31
Before you begin	31
Collect the required items	32
Verify the kit contents	32
Table 8 8/20q Fibre Channel Switch rack mount kit hardware	32
Rack the switch	33
Figure 7 Attaching the rails to the switch	33
Figure 8 Installing the rear mounting brackets	33
Figure 9 Installing the switch and rail assembly	33
Figure 10 Fastening the rail to the front of the rack	34
Figure 11 Fastening the rail to the rear mounting bracket	34
Figure 12 Installing the filler panel	34
Install the transceivers	35
Configure the workstation	35
Configuring the workstation IP address for Ethernet connections	35
Configuring the workstation serial port	35
Apply power to the switch	36
Connect the management station or workstation to the switch	37
Figure 13 Management station and workstation cable connections	37
Configure the switch	37
Simple SAN Connection Manager switch configuration	37
QuickTools switch configuration	37
CLI switch configuration	38
Cable devices to the switch	38
Installing firmware	38
Using QuickTools to install firmware	39
Using the CLI to install firmware	39
One-step firmware installation	40
Custom firmware installation	41
Adding a switch to an existing fabric	41
Installing feature license keys	42
Configuring Call Home to HP Services (optional)	42
Role of the Remote Support Software Manager	42
Role of OSEM and versions required	42
Installation instructions and documentation for SIM, RSP, OSEM, and ISEE	43
RSP requirements for the CMS	43
Infrastructure requirements for implementing Call Home to HP Services	44
Configuring Call Home to HP services	44
Diagnostics and troubleshooting	47
Switch diagnostics	47
Figure 14 Switch LEDs	47
Input power LED is extinguished	47
System fault LED is illuminated	48
Power-On self test diagnostics	48
Heartbeat LED blink patterns	48
Internal firmware failure blink pattern	48
Fatal POST error blink pattern	49
Configuration file system error blink pattern	49
Over-temperature blink pattern	49
Logged-in LED indications	50
Figure 15 Logged-in LED	50
E_Port isolation	50
Excessive port errors	51
Transceiver diagnostics	52
Recovering a switch using maintenance mode	53
Exiting the maintenance menu (option 0)	53
Unpacking a firmware image file in maintenance mode (option 1)	54
Resetting the network configuration in maintenance mode (option 2)	54
Resetting user accounts in maintenance mode (option 3)	54
Copying log files in maintenance mode (option 4)	54
Removing the switch configuration in maintenance mode (option 5)	54
Remaking the file system in maintenance mode (option 6)	54
Resetting the switch in maintenance mode (option 7)	55
Updating the boot loader in maintenance mode (option 8)	55
Regulatory compliance and safety	57
Regulatory compliance	57
Federal Communications Commission notice for Class A equipment	57
Cables	57
Laser device	57
Laser safety warning	57
Certification and classification information	58
Laser product label	58
Figure 16 Class 1 laser product label	58
International notices and statements	58
Canadian notice (avis Canadien)	58
European Union regulatory notice	59
Japanese notice	59
Korean notice	59
Taiwan notice	59
Electrostatic discharge	61
How to prevent electrostatic discharge	61
Grounding methods	61
Technical specifications	63
General specifications	63
Table 9 General specifications	63
Maintainability features	64
Table 10 Maintainability features	64
Fabric management specifications	65
Table 11 Fabric management specifications	65
Weight and physical dimensions	65
Table 12 Switch physical dimensions	65
Electrical specifications	65
Table 13 Electrical specifications	65
Environmental requirements	66
Table 14 Environmental requirements	66
Factory configuration defaults	67
Factory switch configuration	67
Table 15 Switch configuration defaults	67
Factory port configuration	68
Table 16 Port configuration defaults	68
Factory port threshold alarm configuration	69
Table 17 Port threshold alarm configuration defaults	69
Factory zoning configuration	69
Table 18 Zoning configuration defaults	69
Factory SNMP configuration	70
Table 19 SNMP configuration defaults	70
Factory switch services configuration	70
Table 20 Services configuration defaults	70
Factory DNS host name configuration	71
Table 21 DNS host name configuration defaults	71
Factory IP version 4 Ethernet configuration	71
Table 22 IP version 4 Ethernet configuration defaults	71
Factory IP version 6 Ethernet configuration	71
Table 23 IP version 6 Ethernet configuration defaults	71
Factory event logging configuration	72
Table 24 Event logging configuration defaults	72
Factory NTP server configuration	72
Table 25 NTP server configuration defaults	72
Factory timer configuration	72
Table 26 Timer configuration defaults	72
Factory RADIUS configuration	73
Table 27 RADIUS configuration defaults	73
Factory security configuration	73
Table 28 Security configuration defaults	73
Factory Call Home configuration	74
Table 29 Call Home service configuration defaults	74
Glossary	75
Index	79
Numerics	79
A	79
B	79
C	79
D	79
E	79
F	79
G	80
H	80
I	80
L	80
M	80
N	80
O	80
P	80
Q	81
R	81
S	81
T	81
U	81
V	81
W	81

Match case Limit results 1 per page

fabrics, the interoperability mode must be configured to InteropMode=0. Other B-Series or C-Series

switches in the remote fabric need not support NPIV.

NOTE:

Be sure to configure the TR_Port before connecting the remote fabric to the HP

StorageWorks 8/20q Fibre Channel Switch. If the remote fabric is connected to a port on the HP

StorageWorks 8/20q Fibre Channel Switch that is not a TR_Port, the two fabrics may establish an

E_Port connection and the local and remote fabrics may merge. This mixed fabric is not supported .

If the port type is changed to TR_Port after connecting the remote fabric, a port reset may be

required to completely establish the connection.

Map local devices to remote devices and activate the connection. The QuickTools mapping process

creates an inter-fabric zone (IFZ) in the active zone set consisting of the local device, the remote device,

and the TR_Port. When the mapping is complete, QuickTools activates the new zone set.

The name of the inter-fabric zone begins with IFZ followed by the lowest device port WWN followed by

the remaining port WWN, all uppercase, separated by underscores (_). For example, consider the

following local and remote device WWNs:

•

Local device: 21:00:00:e0:8b:0e:d3:59

•

Remote device: 22:00:00:04:cf:a8:7f:2d

The inter-fabric zone name would be:

IFZ_210000E08B0ED359_22000004CFA87F2D

Apply the same inter-fabric zone that was created on the local fabric to the active zoning on the remote

fabric. QuickTools creates a suggested list of commands during the mapping process that, when run on

a remote fabric consisting of HP StorageWorks B-Series or C-Series switches, will make the necessary

zoning changes to the remote fabric. See the

HP StorageWorks 8/20q Fibre Channel Switch

QuickTools Switch Management User Guide

for important details on creating and using this list of

suggested commands.When modifications to the active zoning on both fabrics are complete, the

transparent routing connection becomes active, and the local devices will discover the remote devices.

Switch services

You can configure your switch to suit the demands of your environment by enabling or disabling a variety

of switch services. Familiarize yourself with the following switch services and determine which ones you

need.

•

Telnet

: Provides for the management of the switch over a Telnet connection. Disabling this service is not

recommended. The default is

enabled

•

Secure Shell (SSH)

: Provides for secure remote connections to the switch using SSH. Your workstation

must also use an SSH client. The default is

disabled

•

GUI Management

: Provides for out-of-band management of the switch with Simple SAN Connection

Manager, QuickTools, SNMP, and SMI-S. If this service is disabled, the switch can only be managed

inband or through the serial port. The default is

enabled

•

Inband Management

: Provides for the management of the switch over an inter-switch link using Simple

SAN Connection Manager, QuickTools, SNMP, or management server. If you disable inband

management, you can no longer communicate with that switch by means other than an Ethernet or

serial connection. The default is

enabled

•

Secure Socket Layer (SSL)

: Provides for secure SSL connections for the QuickTools web applet and

SMI-S. This service must be enabled to authenticate users through a Remote Authentication Dial-in

Service (RADIUS) server. To enable secure SSL connections, you must first synchronize the date and time

on the switch and the workstation. Enabling SSL automatically creates a security certificate on the

switch. The default is

disabled

NOTE:

Simple SAN Connection Manager version 1.0 does not support the SSL service. If SSL is

enabled, you will be unable to manage the switch using this version of Simple SAN Connection

Manager.