HP StorageWorks Modular Smart Array 1000 HP StorageWorks MSA1000/500 Chassis R - Page 1
HP StorageWorks Modular Smart Array 1000 Manual
![]() |
View all HP StorageWorks Modular Smart Array 1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Replacement Instructions hp StorageWorks MSA1000/500 Chassis These instructions apply to the MSA1000/500 product families. The part may also be used in other HP products. Please refer to documentation for your specific product for detailed replacement instructions. If the product in which this part is being replaced is still under HP warranty, then the replacement part(s) referred to in these Replacement Instructions is provided under the terms and conditions of the Hewlett-Packard Company Limited Warranty for that product. A copy of this Limited Warranty may be viewed at: http://h18006.www1.hp.com/products/storageworks/warranty.html If this is a trade sale part (product out of warranty), then the replacement part(s) referred to in these Replacement Instructions is provided under HP's express limited warranty statement, which may be viewed at: http://customerops.corp.hp.com/1sw/pdm_om/warranty_support/policies/ 2330100.doc The replacement part takes on either the Limited Warranty Period of the part being replaced or a ninety-day period that begins upon installation of the replacement part, whichever is greater. The information contained on these replacement instructions is subject to change without notice. The only warranty for this replacement product is as noted above. Nothing in these replacement instructions should be construed as constituting an additional warranty. The information provided in these replacement instructions is provided "AS IS" and HP is not liable for technical or editorial errors or omissions contained herein. © Copyright 2004 Hewlett-Packard Development Company, L.P. Please note that this document is protected by federal copyright law and that no part of this document may be copied, reproduced or translated without the prior written consent of Hewlett-Packard Development Company, L.P. Printed in the USA. MSA1000/500 Chassis Replacement Instructions First Edition (April 2004) Part Number: 367469-001 367469- 001 About this document This document details the procedures for replacing a failed MSA1000/500 chassis for HP StorageWorks Modular Smart Array (MSA) storage systems. Before you begin Read the following cautions and information before beginning removal and replacement procedures. Caution: Parts can be damaged by electrostatic discharge. Use proper anti-static protection. Refer to the documentation that shipped with your system for additional information. Caution: It is important to follow these instructions when replacing components in the MSA1000/500. If the procedure is done improperly, it is possible to lose data or damage equipment. Caution: Before replacing this component ensure that steps have been taken to prevent loss of data. Note: Before replacing the chassis it is important to stop all system access (for example, application, system I/O or RAW device file path/s) to the device. Note: Retain the packing materials of the spare chassis to return the faulty chassis. Weight warning WARNING: The MSA1000/500 weighs 50 pounds (22.7 kilograms) when fully assembled. To reduce the risk of personal injury or damage to equipment: ■ Observe local health and safety requirements and guidelines for manual material handling. ■ Obtain adequate assistance to lift and stabilize the MSA1000/500 during installation or removal. ■ Remove all tape drives and blower assemblies/power supplies to reduce the overall weight of the library. Removing the components from the failed chassis Step 1: Preparing the MSA1000/500 for chassis replacement 1. Power off the MSA1000/500. Note: Before disconnecting any cables, label all cables. This ensures their reconnection in the correct configuration. Caution: Use appropriate precautions when handling Fibre Channel cables: ■ Touching the end of a Fibre Channel cable will either damage the cable or cause performance problems, including intermittent difficulties accessing the storage. ■ Whenever a Fibre Channel cable is not connected, replace the protective covers on the ends of the cable. 2. Disconnect the power cables. 3. Disconnect the fibre cables. (MSA1000 only) 4. Disconnect the SCSI cables. 5. Remove the MSA1000/500 from the rack. Step 2: Removing the hot-plug hard drives Caution: Label the hard drives so they can be reinstalled in their original positions. Failure to retain the same configuration can result in loss of data. 1. Press the ejector 1 and pivot the lever 2 to full open position. 2. Pull the drive completely out of the storage system drive bay 3. 3 1 2 Figure 1: Removing an MSA1000/500 hot-plug hard drive Step 3: Removing the hard drive blanks 1. Push the tabs to unlock the MSA1000/500 hard drive blank 1. 2. Continue to press the tabs while sliding the MSA1000/500 hard drive blank out of the drive cage 2. 1 2 Figure 2: Removing an MSA1000/500 hard drive blank Step 4: Removing the Fibre Channel I/O module (MSA1000 only) 1. Slide the port-colored release latch to the right 1. 2. Slide the Fibre Channel I/O module straight out 2. 2 3 1 Figure 3: Removing the Fibre Channel I/O module Step 5: Removing the SCSI I/O module 1. Press the port-colored SCSI I/O latch down 1. 2. Slide the SCSI I/O module straight out 2. 2 2 Figure 4: Removing the SCSI I/O module Step 6: Removing the power supply 1. While pushing up the power supply port-colored module latch 1, pull the power supply out of the enclosure 2. 1 2 Figure 5: Removing the power supply 2. Repeat for the redundant power supply. See other side
![](/manual_guide/products/hewlettpackard-storageworks-modular-smart-array-1000-hp-storageworks-msa1000500-chassis-replacement-instructions-2004-3339c44/1.png)