Home » HP Manuals » Desktops » HP Visualize c200/c240 » Manual Viewer

HP Visualize c200/c240 Browsable CD Booklet - Page 8

WARNING, Installing Patches on a System with ACE Software

Get HP Visualize c200/c240 - SSP Workstation PDF manuals and user guides

View all HP Visualize c200/c240 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

WARNING You must load the Additional Core Enhancements as an entire bundle. HP recommends that you also load the Workstation Quality Pack for HP-UX 10.20 ACE from the Support Plus media. If you load individual patches from the Workstation ACE or the Networking ACE, the on-line Installed Product Database will not indicate that the ACE bundle is installed. This booklet focuses on the case of loading the ACE software from a CD-ROM. However, most of the instructions also apply to DDS (tape) media or updating from a remote depot across a network. The only difference is the speciﬁcation of the Source Depot Type. Installing Patches on a System with ACE Software When the ACE software is loaded on your computer, exercise caution in applying patches from other sources. Before adding any patch to HP-UX, you should compare it to the list of component patches in the ACE bundle. (You can ﬁnd this information in the Release Notes document for the ACE software. Also consult 8

Section	Page
Table of Contents	1
Additional Core Enhancements (ACE)	1
The Workstation Quality Pack ..... 3	1
New Features/Functionality..... 4	1
Visualize-fxe	1
USB Devices	1
Consolidated NFS Patches	1
Automatic Configuration of Graphics Cards	1
IDE CD-ROM Drives	1
Distributed Single Logical Screen	1
Year 2000 Compliance ..... 6	1
System Administration Information ..... 6	1
Updates and Upgrades	1
Using Software Distributor	1
Installing Patches on a System with ACE Software	1
System Administration Tasks ..... 10	1
Cold Installing with ACE Software	1
Updating with ACE Software	1
Loading the Quality Pack	1
Verifying Installation of ACE Software	1
Removing ACE Software from Your Computer ..... 19	1
What does “ACE” mean? An ACE bundle is, as it’s name implies, a collection of enhancements to the...	2
The Workstation Quality Pack	3
The Workstation Quality Pack is an important part of HPs software support strategy. We thoroughly...	3
New Features /Functionality	4
Visualize-fxe	4
Visualize-fxe is HP’s new entry-level, low cost, full-featured 3D graphics card which replaces th...	4
USB Devices	4
New four-port USB Hub (D6804A) and a three-button (no scroll wheel) USB Mouse. The USB Mouse is p...	4
Consolidated NFS Patches	4
HP has combined Networking product enablement patches that deliver the ONC+/NFS Networking ACE pr...	4
Automatic Configuration of Graphics Cards	5
New patches deliver enhancements that preserve the relationship between /dev/crt devices special ...	5
IDE CD-ROM Drives	5
Minor changes have been made to the HP-UX IDE driver to accommodate slight differences in the imp...	5
Distributed Single Logical Screen (SLS/d)	5
This functionality was originally released in 10.20 ACE (June 1999) and cooperates with HP OpenGL...	5
The significant changes are:	5
• Improved mouse performance when running display list OpenGL applications.	5
• Ability to move the default visual to the image planes.	5
Year 2000 Compliance	6
The Year 2000 patches in the Quality Pack are necessary to make your computer Year 2000 compliant...	6
In order to make your systems fully Year 2000 compliant, you may also need to upgrade application...	6
http://www.hp.com/go/year2000	6
System Administration Information	6
Installing ACE bundles extend the functionality of HP-UX 10.20 You must install HP-UX 10.20 along...	6
Updates and Upgrades	6
If you are running HP-UX 10.0, 10.01, or 10.10, you must update your system to HP-UX 10.20 before...	6
http://www.software.hp.com/OS_transition/	7
Using Software Distributor	7
This booklet describes how to load ACE software for HP-UX 10.20 on a PA-RISC workstation using th...	7
WARNING	8
You must load the Additional Core Enhancements as	8
an entire bundle. HP recommends that you also load	8
the Workstation Quality Pack for HP-UX 10.20 ACE	8
from the Support Plus media. If you load individual	8
patches from the Workstation ACE or the Networking	8
ACE, the on-line Installed Product Database will not	8
indicate that the ACE bundle is installed.	8
This booklet focuses on the case of loading the ACE software from a CD-ROM. However, most of the ...	8
Installing Patches on a System with ACE Software	8
When the ACE software is loaded on your computer, exercise caution in applying patches from other...	8
If you cannot determine whether a specific patch is newer than the ACE software, contact your loc...	9
Do not use the ACE software bundle as a source of individual patches to HP-UX. You should continu...	9
System Administrator Tasks	10
The following information is an abridged set of instructions to perform common system administrat...	10
Cold Installing with ACE Software	10
You can cold install from the Install/Update/Recovery CD- ROM that is packaged with this booklet....	10
The version of the install utility on the ACE install media will automatically load both the base...	10
The following is an abbreviated description of the cold install process. It focuses on the steps ...	10
1. Load the ACE install media in the CD-ROM drive for your workstation and boot the system. Follo...	10
2. Select the CD-ROM drive as your boot device.	11
3. Select the cold install action in the Install HP-UX menu andcontinue as usual.	11
4. Stop when you reach the install utility screen with this title:	11
HP-UX Install Utility - View/Modify Basic Configuration	11
If you wish to load the ONC+ bundle as part of this installation, then mark Load 10.20 Networking...	11
Resume the install process, by selecting OK.	11
5. Continue with the install process as you normally would. After you have responded to all quest...	12
6. Once the install utility completes loading the software, it will reboot your workstation.	12
7. After your workstation has rebooted, you may proceed with the instructions on “Loading the Qua...	12
8. See the section below on Verifying Installation of ACE Software for information about how to ...	12
Updating HP-UX with ACE Software	13
If you are already running HP-UX 10.20, you are ready to use SD-UX to load ACE software on your s...	13
1. Load the Install/Update/Recovery CD-ROM in yourdrive and mount it, if necessary. (You can use...	13
2. Select Software Management from the main SAM menu.	13
3. Select Install Software to Local Host to invoke swinstall.	13
4. Specify the following information:	14
Source Depot Type: Local CDROM	14
(If you are loading software from DDS media, then select the Local Tape option.)	14
Source Host Name: <hostname>	14
Source Depot Path: <CD mount path>	14
After verifying that this information is correct, select the“OK” button.	14
5. SAM will list the software bundles and products on the CD. Go to the Actions menu, and select...	14
Note that the Match Target approach will load all ACE bundles from the ACE media onto your system...	14
6. Go to the Actions menu and select the Install	15
(analysis)... item.	15
7. After the analysis phase completes, you can select the Logfile button to check for errors, w...	15
8. Following the install phase, the swinstall command will reboot your workstation. (This is nece...	15
9. After your system reboots, you have completed the firststage of updating with the ACE softwar...	15
Loading the Quality Pack	16
1. Insert the Support Plus CD-ROM and mount it.	16
2. Select Software Management from the main SAM menu.	16
3. Select Install Software to Local Host to invoke	16
swinstall.	16
4. Specify the following information:	16
Source Depot Type: <CD mount path>	16
Source Host Name: <hostname>	16
Source Depot Path: <cdrom>/700QPK1020	16
(where <cdrom> refers to the mount point for the CD-ROM)	16
Once you have verified that this information is correct, select the “OK” button.	16
5. SAM will list the Quality Pack bundle(s) in the Support Plusdepot. Go to the Actions menu, an...	16
6. Go to the Actions menu and select the Install(analysis)...item.	17
7. After the analysis phase completes, you can select the “Logfile” button to check for errors, w...	17
8. Following the install phase, the swinstall command will reboot your workstation. (This is nece...	17
9. After your system has rebooted, you have finished updating with the ACE software. You can now ...	17
Verifying Installation of ACE Software	18
To verify that ACE software is loaded on your computer, execute this command:	18
/usr/sbin/swlist -l bundle \| grep ACE	18
The output of these commands is a list of all ACE bundles resident on your computer. See the tabl...	18
For up-to-date information about ACE bundles for workstations or copies of older ACD bundles, che...	18
http://www.software.hp.com/ACE	18
Removing ACE Software from Your Computer	19
Removing an ACE bundle or the Quality Pack from your system can lead to unexpected consequences, ...	19
The ACE bundles and Quality Packs are collections of patches. As such, they interact with each ot...	19
If you choose to remove an ACE bundle or Quality Pack from your system, first make a backup copy ...	19
Related HP-UX Documentation	20
Upgrading from HP-UX 9.x to 10.x	20
p/n B3782-90073	20
Installing and Updating HP-UX 10.x	20
p/n B2355-90126	20
Installing and Updating HP-UX Workstation Additional Core Enhancements for 10.20	20
p/n B3782-90795	20
Managing HP-UX Software with SD-UX (for HP-UX 10.20)	20
p/n B2355-90107	20
Support Plus User’s Guide	20
p/n B3782-90812	20