HP Visualize c3000 hp Visualize b1000 and c3000 workstations service handbook - Page 88

cord from the AC power outlet.

Page 88 highlights

Field Replaceable Units WARNING For all removal and replacement procedures in this chapter, you must power off the workstation and unplug the workstation power cord from the AC power outlet. NOTE To maintain FCC/EMI compliance, verify that all covers are replaced and that all screws are properly seated. Use the following tools to remove or replace FRUs: • Torx T-10 driver • Torx T-15 driver • Light duty flat blade screw driver with 6-inch (150mm) blade • Needle-nose pliers • ESD equipment (see "Electrostatic Discharge (ESD) Precautions" on page 196) • Pen knife NOTE To maintain FCC/EMI compliance, verify that all covers are replaced and that all gasket material is intact. Figure 4-1. shows an exploded view of the internal components (FRUs) in the B1000 and C3000 workstations. Refer to this figure for the locations of the various workstation FRUs while performing the FRU removal and replacement procedures in this chapter. 88 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239

88
Chapter 4
Field Replaceable Units
WARNING
For all removal and replacement procedures in this chapter, you
must power off the workstation and unplug the workstation power
cord from the AC power outlet.
NOTE
To maintain FCC/EMI compliance, verify that all covers are replaced and
that all screws are properly seated.
Use the following tools to remove or replace FRUs:
Torx T-10 driver
Torx T-15 driver
Light duty flat blade screw driver with 6-inch (150mm) blade
Needle-nose pliers
ESD equipment (see “Electrostatic Discharge (ESD) Precautions” on page 196)
Pen knife
NOTE
To maintain FCC/EMI compliance, verify that all covers are replaced and
that all gasket material is intact.
Figure 4-1. shows an exploded view of the internal components (FRUs) in the B1000 and
C3000 workstations.
Refer to this figure for the locations of the various workstation FRUs while performing the
FRU removal and replacement procedures in this chapter.