HP Xw6400 Remote Graphics Software 4.2.0 User Guide - Page 89

RGS Sender Properties

Get HP Xw6400 - Workstation - 4 GB RAM PDF manuals and user guides
UPC - 882780645493
View all HP Xw6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Using Remote Graphics Software Rgreceiver.Usb.IsEnabled=bool If set to "1", remote USB will be enabled. If set to "0", all remote USB will be disabled and no network bandwidth will be consumed for remote USB. This property only applies to HP Blade Workstation Client. Rgreceiver.Usb.ActiveSession=int When the RGS Receiver is in Directory Mode or Enterprise Service Mode, the Receiver can connect to one or more RGS Senders. This property will specify the RGS Sender that remote USB will be connected to. To have all remote USB go to the first sender, use value zero. To have all remote USB go to the second sender, use value one, and so on. Remote USB can only go to one sender at a time. To change the sender, all senders must be disconnected. Then, enter a new value and reconnect all senders. The default value is zero - the first sender to be connected. This property only applies to HP Blade Workstation Client. RGS Sender Properties All of the following properties are used by the RGS Sender, and can be set from the command line or from the RGS Sender property configuration file (rgsenderconfig). General Properties: Rgsender.IsRdpLogoutDetected=bool The methods provided by Microsoft to close a connection through Remote Desktop Protocol (RDP) work quickly when the user disconnects from the RDP session. If the user logs out of the RDP session, the RGS Sender will be unable to access the desktop for about 60 seconds. If set to "1", the desktop will be available to the user through RGS as soon as possible. The RGS Sender will monitor the RDP session for a logout and begin the process of making the desktop available as soon as the logout is detected. If set to "0", the RGS Sender will not monitor the RDP session for a logout. This property only applies to Windows versions of the RGS Sender. Rgsender.IsCopyRegionEnabled=bool If set to "1", RGS Copy Regions are sent from the Sender to the Receiver. If set to "0", RGS Copy Regions are turned off and will be sent to the Receiver as Image Update Regions. This is for advanced use and should not be set. The default value is "1" - send RGS Copy Regions. Rgsender.IsRegionLimitEnabled=bool Used to limit the number of update rectangles in a update region. This is for advanced use and should not be set. The default value is 0 - don't limit regions. 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
Using Remote Graphics Software
81
Rgreceiver.Usb.IsEnabled
=bool
If set to "1", remote USB will be enabled. If set to "0", all remote USB will be
disabled and no network bandwidth will be consumed for remote USB.
This property only applies to HP Blade Workstation Client.
Rgreceiver.Usb.ActiveSession
=int
When the RGS Receiver is in Directory Mode or Enterprise Service Mode, the
Receiver can connect to one or more RGS Senders. This property will specify the RGS
Sender that remote USB will be connected to. To have all remote USB go to the first
sender, use value zero. To have all remote USB go to the second sender, use value
one, and so on. Remote USB can only go to one sender at a time. To change the
sender, all senders must be disconnected. Then, enter a new value and reconnect all
senders. The default value is zero - the first sender to be connected.
This property only applies to HP Blade Workstation Client.
RGS Sender Properties
All of the following properties are used by the RGS Sender, and can be set from the
command line or from the RGS Sender property configuration file (
rgsenderconfig
).
General Properties
:
Rgsender.IsRdpLogoutDetected
=bool
The methods provided by Microsoft to close a connection through Remote Desktop
Protocol (RDP) work quickly when the user disconnects from the RDP session. If the
user logs out of the RDP session, the RGS Sender will be unable to access the
desktop for about 60 seconds. If set to "1", the desktop will be available to the user
through RGS as soon as possible. The RGS Sender will monitor the RDP session for a
logout and begin the process of making the desktop available as soon as the logout
is detected. If set to "0", the RGS Sender will not monitor the RDP session for a
logout.
This property only applies to Windows versions of the RGS Sender.
Rgsender.IsCopyRegionEnabled
=bool
If set to "1", RGS Copy Regions are sent from the Sender to the Receiver. If set to
"0", RGS Copy Regions are turned off and will be sent to the Receiver as Image
Update Regions. This is for advanced use and should not be set. The default value is
"1" - send RGS Copy Regions.
Rgsender.IsRegionLimitEnabled
=bool
Used to limit the number of update rectangles in a update region. This is for
advanced use and should not be set. The default value is 0 - don't limit regions.