HP Z420 LSI SAS RAID Host Bus Adapter installation - Page 4

Step 3-Configuring the cabling - workstations

Get HP Z420 PDF manuals and user guides View all HP Z420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Step 3-Configuring the cabling The RAID controller card may be used to control hard drives located in the internal and external drive bays. The data cable connections for RAID controller cards differ between workstation models. To determine the correct connection for your hard drives, identify the applicable HP workstation model and the location of the hard drive being connected in the following table. To connect existing hard drives, disconnect the existing data cables from the system board and choose the correct connection type. The hard drive LED cable connection is similar for most HP workstation models. Table 1 Data cable configuration guide HP workstation model Location of hard drive Connection type Description HP Z400 and Z420 Workstations ● Internal hard drive bay ● External drive bay Connecting standard data cables on page 7 Use the data cable provided with the hard drive to connect the hard drive to the RAID controller card. For SAS drives, refer to specific instructions on data cabling and adapter types in Connecting standard data cables on page 7. HP Z600 and Z620* Workstations ● Internal hard drive bay Connecting pre-installed data cables on page 5 The pre-installed data cables from the internal hard drives are disconnected from the system board and connected to the appropriate port connectors on the RAID controller card in Connecting pre-installed data cables on page 5. HP Z600 and Z620* Workstations ● External drive bay Connecting standard data cables on page 7 Use the data cable provided with the hard drive to connect the hard drive to the RAID controller card. For SAS drives, refer to specific instructions on data cabling and adapter types in Connecting standard data cables on page 7. IMPORTANT: * The HP Z620 Workstation requires use of the provided 4x SATA cable to extend the data cable length. Attach the 4x SATA cable extender to the RAID controller card, then connect the internal hard drive bay data cables or the external drive bay cable to the appropriate port on the other end of the 4x SATA cable. 4 LSI SAS RAID Host Bus Adapter installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Step 3—Configuring the cabling
The RAID controller card may be used to control hard drives located in the internal and external drive
bays.
The data cable connections for RAID controller cards differ between workstation models. To determine
the correct connection for your hard drives, identify the applicable HP workstation model and the
location of the hard drive being connected in the following table. To connect existing hard drives,
disconnect the existing data cables from the system board and choose the correct connection type.
The hard drive LED cable connection is similar for most HP workstation models.
Table 1
Data cable configuration guide
HP workstation
model
Location of hard drive
Connection type
Description
HP Z400 and Z420
Workstations
●
Internal hard drive bay
●
External drive bay
Connecting standard data
cables
on page
7
Use the data cable provided with
the hard drive to connect the hard
drive to the RAID controller card.
For SAS drives, refer to specific
instructions on data cabling and
adapter types in
Connecting
standard data cables
on page
7.
HP Z600 and Z620*
Workstations
●
Internal hard drive bay
Connecting pre-installed
data cables
on page
5
The pre-installed data cables from
the internal hard drives are
disconnected from the system
board and connected to the
appropriate port connectors on the
RAID controller card in
Connecting
pre-installed data cables
on page
5.
HP Z600 and Z620*
Workstations
●
External drive bay
Connecting standard data
cables
on page
7
Use the data cable provided with
the hard drive to connect the hard
drive to the RAID controller card.
For SAS drives, refer to specific
instructions on data cabling and
adapter types in
Connecting
standard data cables
on page
7.
IMPORTANT:
* The HP Z620 Workstation requires use of the provided 4x SATA cable to extend the data cable length.
Attach the 4x SATA cable extender to the RAID controller card, then connect the internal hard drive bay data cables or the
external drive bay cable to the appropriate port on the other end of the 4x SATA cable.
4
LSI SAS RAID Host Bus Adapter installation