HP Z600 HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H
HP Z600 - Workstation - 6 GB RAM Manual
UPC - 884962074053
View all HP Z600 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Z600 manual content summary:
- HP Z600 | HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H - Page 1
in HP Workstations, such as the HP Z600 Workstation series, may be different. Complete installation and removal procedures for this product are included in the service guide for your workstation model, available at http://www.hp.com/support/manuals. © 2004-2010 Hewlett-Packard Development - HP Z600 | HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H - Page 2
power cord grounding plug. The grounding plug is an important safety feature. - Plug the power Guide. It describes proper computer setup, posture, health, and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located at http://www.hp - HP Z600 | HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H - Page 3
models vary, and all illustrations are examples only. For product-specific information, see the service guide for your HP computer at http://www.hp.com/support/manuals before beginning installation. The attachment point for the Hood Sensor may be located on the front panel, back panel, or sheet - HP Z600 | HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H - Page 4
so it is not interfering with other system board connectors or computer components. NOTE: To locate system components on HP Workstations, see the service label on the side access panel. On some HP Workstations, such as the HP Z600 Workstation series, the Solenoid Lock cable does not connect to the - HP Z600 | HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H - Page 5
> Save Changes and Exit. Remote security management It is possible to remotely lock and unlock the Solenoid Lock using Remote Access Software. Refer to www.hp.com/go/hpcmi for tools you can use to remotely manage the computer and BIOS settings in a networked environment. ENWW Reassembling the - HP Z600 | HP xw and Z Series Workstations - Installing an HP Solenoid Lock and H - Page 6
and any external devices, and then disconnect the power cord from the power outlet. 2. Lay the computer on its side with the cover facing up. 3. Using the FailSafe Key included in this kit, remove the two tamper-resistant screws that secure the Solenoid Lock to the chassis. 4. After the screws
Installing an HP Solenoid Lock and Hood
Sensor
Introduction
The side access panel Solenoid Lock is designed to prevent unauthorized removal of the computer
cover. The side access panel may be locked by using a local or remote signal-controlled solenoid.
The Hood Sensor is designed to notify the user of any removal of the computer cover.
Kit contents
●
Solenoid Lock assembly, including solenoid, bracket, and cable
●
Two tamper-resistant screws
●
Solenoid Lock FailSafe Key
●
Sensor and power cable
●
Sensor bracket
●
Two sensor bracket screws
●
Warranty information
●
This installation guide
Before you begin
To determine the compatibility of this product with your HP computer, see
QuickSpecs
online at
go/productbulletin
.
Installing the Solenoid Lock and Hood Sensor in HP Workstations
Installations in HP Workstations, such as the HP Z600 Workstation series, may be different.
Complete installation and removal procedures for this product are included in the service guide for
your workstation model, available at
support/manuals
.
© 2004–2010 Hewlett-Packard Development Company, L.P. Printed in the U.S.
ENWW
Introduction
1