HP Z600 Rack Mounting Kits for the Z400, Z600, and Z800 Workstations - Page 2

E3662B, E7590A, J1450B or - rack mount

Page 2 highlights

Key Product Features - Z600/Z800 Rack Kit (NN124AA): This kit features an enterprise-class three section ball-bearing extension slide. The slides are fully extendible, so the unit can slide totally out of the rack for servicing. This makes it very convenient to add memory, hard disk drives, optical disk drives, option cards, etc. without removing the computer from the rack. The Rack kit rails snap into the HP rack without using tools, however, screws are needed to attach the inner slide and mounting flanges to the computer chassis. The top mounting holes are concealed by the top plastic trim piece, which must be removed along with the rear handle to attach the inner slide and mounting flanges. The mounting is very similar to that used for the xw6x00 rack mount kit (DY663A), but with the depth adjustability of the xw8x00 rack mount kit (DY664A). Some of our customers need to rack mount into racks that are only 24 inches deep (such as those commonly used in the Broadcast industry), instead of the 29-30 inch deep racks that are commonly used in the IT industry (including HP racks), so adjustability was also an important objective. The new rack mount kit is adjustable to accommodate racks that are 24 - 30 inches deep. The rails come pre-adjusted to fit the standard HP racks for convenience. For more information about the Z600/Z800 Rack Mount Kit, see: http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01689230/c01689230.pdf Figure 1. Z600/Z800 Rack Mount - Cutaway showing unit installed in rack Rack Columns Slide Rails Figure 2. Z600/z800 Rack Mount - Slide rails extended Rack Columns NOTE: Legacy Rack customers will need to also order part number WD587AA to install the Rack Mount Slide Kit You are a Legacy Rack customer if your rack model is any of the following; E3660B, E3661B, E3662B, E7590A, J1450B or J1487A/B. Slide Rails © 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. XXX 2009

  • 1
  • 2

© 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP
products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as
constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. XXX 2009
K
ey Product Features – Z600/Z800 Rack Kit
(NN124AA)
:
This kit features an enterprise-class three section ball-bearing extension slide.
The slides are fully extendible, so the unit can slide totally
out of the rack for servicing.
This makes it very convenient to add memory, hard disk drives, optical disk drives, option cards, etc. without
removing the computer from the rack.
The Rack kit rails snap into the HP rack without using tools, however, screws are needed to attach the inner slide and mounting flanges to
the computer chassis.
The top mounting holes are concealed by the top plastic trim piece, which must be removed along with the rear
handle to attach the inner slide and mounting flanges.
The mounting is very similar to that used for the xw6x00 rack mount kit (DY663A),
but with the depth adjustability of the xw8x00 rack mount kit (DY664A). Some of our customers need to rack mount into racks that are
only 24 inches deep (such as those commonly used in the Broadcast industry), instead of the 29-30 inch deep racks that are commonly
used in the IT industry (including HP racks), so adjustability was also an important objective. The new rack mount kit is adjustable to
accommodate racks that are 24 – 30 inches deep. The rails come pre-adjusted to fit the standard HP racks for convenience.
For more information about the Z600/Z800 Rack Mount Kit, see:
Figure 1.
Z600/Z800 Rack Mount - Cutaway showing unit installed in rack
Figure 2.
Z600/z800 Rack Mount - Slide rails extended
Rack
Columns
Slide Rails
Slide Rails
Rack
Columns
NOTE:
Legacy Rack customers will
need to also order part number
WD587AA to install the Rack
Mount Slide Kit
You are a Legacy Rack customer
if your rack model is any of the
following; E3660B, E3661B,
E3662B, E7590A, J1450B or
J1487A/B.