Home » HP Manuals » Desktops » HP b2600 » Manual Viewer

HP b2600 hp workstation b2600 parts removal and replacement guide (a6070-90011 - Page 101

D-7, Unscrew the Four Flexible Disk Drive Mounting Screws, not keyed, Removing the Flexible

Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Remove/Replace Flexible Disk Drives Removing the Flexible Disk Drive 8. Unscrew the four bracket mounting screws from the flexible disk drive and remove the flexible disk drive from its bracket. See Figure D-7. Figure D-7 Unscrew the Four Flexible Disk Drive Mounting Screws Bracket Mounting Screws Bracket Mounting Screws Flexible Disk Drive Flexible Disk Drive Bracket Removing the SCSI Cable Because there are special considerations you should know regarding the removal of the SCSI cable, this section explains some of those considerations. This section also explains how to remove the SCSI cable from your workstation's PCI cage. Here are some important points to remember regarding the SCSI card and cable. • The SCSI card can be installed in any of the unused slots in your workstation's PCI cage; however, for ease of cable routing it is best to install your SCSI card in slot 4 of the PCI cage. • The SCSI cable is long enough to allow you to run it through the flexible disk drive bay and out its front. This makes it easy for you to connect your power and SCSI cable connectors to the flexible disk drive. • The connectors on both ends of the SCSI cable are keyed to allow for proper pin connection. However, the flexible disk drive's connector is not keyed and you have to align the red line on the SCSI cable with the left side (as viewed from the back of the flexible disk drive) of the flexible disk drive's SCSI connector. To remove the SCSI card and cable, follow this procedure: 1. Complete the procedure in the section "Removing the Flexible Disk Drive" found in this appendix. Appendix D 101

Section	Page
Parts Removal and Replacement Guide	1
Parts Removal and Replacement Guide	1
Parts Removal and Replacement Guide	1
HP B2600 Workstations	1
Manufacturing Part Number: A6070-90010	1
Edition E0601	1
Notice	2
Notice	2
Restricted Rights Legend	2
Restricted Rights Legend	2
© Copyright 2001	2
© Copyright 2001	2
Hewlett-Packard Company. All Rights Reserved. This document contains proprietary information that...	2
© Copyright 1980, 1984	2
© Copyright 1980, 1984	2
AT&T, Inc.	2
© Copyright 1979, 1980, 1983	2
© Copyright 1979, 1980, 1983	2
The Regents of the University of California. This software and documentation is based in part on ...	2
Preface	7
Preface	7
Installation Notice	7
Installation Notice	7
Related Manuals	7
Related Manuals	7
• Installation Poster for the HP B2600 Workstation	7
• Installation Poster for the HP B2600 Workstation	7
• Installation Poster for the HP B2600 Workstation	7
• Getting Started Guide for the HP B2600 Workstation	7
• Getting Started Guide for the HP B2600 Workstation	7
• Technical Reference for the HP B2600 Workstation	7
• Technical Reference for the HP B2600 Workstation	7
• Common Desktop Environment (CDE) User’s Guide	7
• Common Desktop Environment (CDE) User’s Guide	7
• Common Desktop Environment (CDE) User’s Guide	7
• Configuring HP-UX for Peripherals	7
• Configuring HP-UX for Peripherals	7
• HP-UX System Administration Tasks	7
• HP-UX System Administration Tasks	7
• HP CDE Getting Started Guide	7
• HP CDE Getting Started Guide	7
• Managing Systems and Workgroups	7
• Managing Systems and Workgroups	7
• Using HP-UX	7
• Using HP-UX	7
• Using Your HP Workstation	7
• Using Your HP Workstation	7
Revision History	8
Revision History	8
Edition	8
Edition	8
Edition	8
Revision History	8
E0601	8
E0601	8
First Printing	8
Problems, Questions, and Suggestions	8
Problems, Questions, and Suggestions	8
Electrostatic Discharge (ESD) Precautions	8
Electrostatic Discharge (ESD) Precautions	8
ESD (electrostatic discharge)	8
Electrostatic discharge (ESD)	8
• Work on a static-free mat.	8
• Work on a static-free mat.	8
• Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your...	8
• Create a common ground for the equipment you are working on by connecting the static-free mat, ...	8
• Keep uninstalled printed circuit boards in their protective antistatic bags.	8
• Handle printed circuit boards by their edges, once you have removed them from their protective ...	8
1 Remove/Replace System Components	9
1 Remove/Replace System Components	9
Chapter Overview	10
Chapter Overview	10
• Tools Required — a list of tools necessary for removing and replacing system components.	10
• Tools Required — a list of tools necessary for removing and replacing system components.	10
• Removing/Replacing System Components — a set of procedures for removing/replacing: front bezel,...	10
WARNING For most of the installation and removal procedures in this chapter, you must power off t...	10
NOTE To maintain FCC/EMI compliance, verify that all covers are replaced and that all screws are ...	10
Workstation Configurations	10
Workstation Configurations	10
http://www.hp.com/workstations	10
Tools Required	11
Tools Required	11
• Light-duty flat blade screwdriver with 6-inch (150 mm) blade	11
• Light-duty flat blade screwdriver with 6-inch (150 mm) blade	11
• Number 2 Phillips screwdriver with 6-inch (150mm) blade	11
• T-10 and T-15 Torx driver	11
• ESD equipment (see the “Electrostatic Discharge (ESD) Precautions” section later in this chapte...	11
Removing/Replacing System Components	12
Removing/Replacing System Components	12
NOTE If you need to install a new system component, simply follow the procedures for	12
Electrostatic Discharge (ESD) Precautions	12
Electrostatic Discharge (ESD) Precautions	12
• Work on a static-free mat.	12
• Work on a static-free mat.	12
• Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your...	12
• Create a common ground for the equipment you are working on by connecting the static-free mat, ...	12
• Keep uninstalled printed circuit boards in their protective antistatic bags.	12
• Handle printed circuit boards by their edges, once you have removed them from their protective ...	12
Prerequisite for Using the Procedures in this Chapter	13
Prerequisite for Using the Procedures in this Chapter	13
1. Power off the workstation (either by executing	13
1. Power off the workstation (either by executing	13
2. Unplug the workstation power cord and all peripheral devices from AC power outlets. If you are...	13
3. Attach the static-grounding wrist strap by following the instructions on the package. Attach t...	13
NOTE To make access to the internal components easier, you may want to place the workstation on a...	13
CAUTION This workstation is designated for two-person lifting; it weighs approximately 35.0 pound...	13
Removing the Front Bezel and Top Cover	14
Removing the Front Bezel and Top Cover	14
Removing the Front Bezel and Top Cover	14
Removing the Front Bezel and Top Cover	14
1. Turn your workstation off and unplug it.	14
1. Turn your workstation off and unplug it.	14
2. Lay your workstation on a soft anti-static surface with the HP logo text in the upright position.	14
3. Press in on both release buttons found on the ends of the bezel and pull outward from the work...	14
Figure11. Front Bezel and Top Cover Removal	14
Figure11. Front Bezel and Top Cover Removal	14
<GRAPHIC>	15
Replacing the Front Bezel and Top Cover	15
Replacing the Front Bezel and Top Cover	15
Replacing the Front Bezel and Top Cover	15
1. Slide the top cover back on the workstation and secure it by screwing in the captive screws.	15
1. Slide the top cover back on the workstation and secure it by screwing in the captive screws.	15
2. Next, push the bezel in place on the front of the workstation. See	15
Figure12. Front Bezel and Top Cover Replacement	15
Figure12. Front Bezel and Top Cover Replacement	15
<GRAPHIC>	16
Removing Memory DIMMs	16
1. Complete the procedure in the section	16
1. Complete the procedure in the section	16
2. Press downward on the tabs that are located on both ends of the memory card slots. See	16
Figure13. Pressing Down on the Memory Slot Tabs	16
Figure13. Pressing Down on the Memory Slot Tabs	16
<GRAPHIC>	16
Figure14. Lifting a DIMM Card Out of the Memory Slot	16
Figure14. Lifting a DIMM Card Out of the Memory Slot	16
<GRAPHIC>	17
Memory Configuration	17
Figure15. Memory Loading Sequence in the HP B2600	17
Figure15. Memory Loading Sequence in the HP B2600	17
<GRAPHIC>	18
Replacing Memory DIMMs	18
1. Remove the current DIMM(s) if you have not already done this. Otherwise, skip this step. To re...	18
1. Remove the current DIMM(s) if you have not already done this. Otherwise, skip this step. To re...	18
2. Determine the appropriate memory slot(s) for your DIMM card(s). See	18
Figure16. Memory Loading Sequence in the HP B2600	18
Figure16. Memory Loading Sequence in the HP B2600	18
<GRAPHIC>	19
Figure17. Inserting the DIMM Card into a Memory Slot	19
Figure17. Inserting the DIMM Card into a Memory Slot	19
<GRAPHIC>	19
5. Connect and turn on the power to your system.	19
6. Determine that your memory installation was successful by executing the	19
Removing the CD Drive	20
Removing the CD Drive	20
1. Complete the procedure in the section	20
1. Complete the procedure in the section	20
2. Disconnect the CD drive control cable by pulling up on its pull tab and disconnect the power c...	20
Figure18. Disconnecting the CD Drive Control Cable	20
Figure18. Disconnecting the CD Drive Control Cable	20
<GRAPHIC>	20
4. Press in on the retainer clips on both sides of the CD drive bay and pull toward you. See	21
5. Take the back cover off the CD drive bay by lifting up on the raised portion of the back cover...	21
Figure111. Removing the CD Drive Bay’s Back Cover	21
Figure111. Removing the CD Drive Bay’s Back Cover	21
<GRAPHIC>	22
7. Unscrew the four CD drive mounting screws located on both sides of the CD drive bay. See	22
Figure113. Unscrew the Four CD Drive Mounting Screws	22
Figure113. Unscrew the Four CD Drive Mounting Screws	22
<GRAPHIC>	23
Replacing the CD Drive	24
Replacing the CD Drive	24
1. Remove the current CD drive if you have not already done this. Otherwise, skip this step. To r...	24
1. Remove the current CD drive if you have not already done this. Otherwise, skip this step. To r...	24
2. Slide the CD drive into the CD drive bay. See	24
3. Screw the four CD drive mounting screws into their threaded holes located on both sides of the...	24
Figure116. Screw in the Four CD Drive Mounting Screws	24
Figure116. Screw in the Four CD Drive Mounting Screws	24
<GRAPHIC>	25
5. Replace the back cover on the CD drive bay by inserting the hinge tabs located on the CD drive...	25
6. Slide the CD drive bay and CD drive back into the workstation. You will hear the retainer clip...	26
7. Connect the CD drive power cable by pushing it into its connector on the system board and conn...	26
Figure120. Connecting the CD Drive Power and Control Cables	26
Figure120. Connecting the CD Drive Power and Control Cables	26
<GRAPHIC>	27
9. Complete the procedure in the section	27
10. Connect and turn on the power to your system.	27
11. Determine that your CD drive replacement was successful by executing the	27
Removing the PCI Cage, I/O Card and PCI Backplane Board	28
Removing the PCI Cage, I/O Card and PCI Backplane Board	28
PCI Cage Removal	28
PCI Cage Removal	28
1. Complete the procedure in the section	28
1. Complete the procedure in the section	28
2. Complete the procedure in the section	28
3. Lift up on the PCI cage handle (	28
Figure122. Lifting Up on the PCI Cage Handle	28
Figure122. Lifting Up on the PCI Cage Handle	28
<GRAPHIC>	28
Figure123. Removing the PCI Cage from the System	28
Figure123. Removing the PCI Cage from the System	28
<GRAPHIC>	29
I/O Card Removal	29
1. Set the PCI cage on an anti-static surface and remove the PCI cage cover. See	29
1. Set the PCI cage on an anti-static surface and remove the PCI cage cover. See	29
Figure124. Removing the PCI Cage Cover	29
Figure124. Removing the PCI Cage Cover	29
<GRAPHIC>	29
Figure125. Unscrewing the I/O Card’s Bulkhead Screw	29
Figure125. Unscrewing the I/O Card’s Bulkhead Screw	29
<GRAPHIC>	30
Figure126. Removing the I/O Card from Its PCI Slot	30
Figure126. Removing the I/O Card from Its PCI Slot	30
<GRAPHIC>	30
PCI Backplane Board Removal	30
PCI Backplane Board Removal	30
1. Unscrew the three T-15 Torx screws. See	30
1. Unscrew the three T-15 Torx screws. See	30
Figure127. Unscrew the PCI Backplane’s Three T-15 Torx Screws	30
Figure127. Unscrew the PCI Backplane’s Three T-15 Torx Screws	30
<GRAPHIC>	31
Figure128. Removing the PCI Backplane Board	31
Figure128. Removing the PCI Backplane Board	31
<GRAPHIC>	32
PCI Card Guide Removal	32
1. Push the card guide forward with your thumb in the direction of the large arrow and at the sam...	32
1. Push the card guide forward with your thumb in the direction of the large arrow and at the sam...	32
Figure129. Pushing the Card Guide Forward and Down	32
Figure129. Pushing the Card Guide Forward and Down	32
<GRAPHIC>	32
Figure130. Removing the Card Guide from the PCI Cover	32
Figure130. Removing the Card Guide from the PCI Cover	32
<GRAPHIC>	33
Replacing the PCI Cage, I/O Card and PCI Backplane Board	33
PCI Backplane Board Replacement	33
PCI Backplane Board Replacement	33
1. Remove the current CD drive, DAT drive or flexible disk drive if you have not already done thi...	33
1. Remove the current CD drive, DAT drive or flexible disk drive if you have not already done thi...	33
2. Slide the PCI backplane board onto the PCI cage’s standoffs. See	33
Figure131. Replacing the PCI Backplane Board	33
Figure131. Replacing the PCI Backplane Board	33
<GRAPHIC>	33
Figure132. Screw in the PCI Backplane Board’s Three Screws	33
Figure132. Screw in the PCI Backplane Board’s Three Screws	33
<GRAPHIC>	34
I/O Card Replacement	34
1. Replace the PCI backplane board in the PCI cage if you have not already done this. Otherwise, ...	34
1. Replace the PCI backplane board in the PCI cage if you have not already done this. Otherwise, ...	34
2. Remove the I/O card from its anti-static bag, which protects it from any possible electro-stat...	34
3. Grasp the I/O card’s bulkhead and the back edge and insert it into its PCI slot. See	34
Figure133. Inserting the I/O Card into its PCI Slot	34
Figure133. Inserting the I/O Card into its PCI Slot	34
<GRAPHIC>	34
Figure134. Screwing in the I/O Card’s Bulkhead Screw	34
Figure134. Screwing in the I/O Card’s Bulkhead Screw	34
<GRAPHIC>	35
Figure135. Replacing the PCI Cage Cover	35
Figure135. Replacing the PCI Cage Cover	35
<GRAPHIC>	35
PCI Cage Replacement	35
1. Replace the I/O card(s) in the PCI cage if you have not already done this. Otherwise, skip thi...	35
1. Replace the I/O card(s) in the PCI cage if you have not already done this. Otherwise, skip thi...	35
2. Push down on the PCI cage handle and on the back of the PCI cage. Next, rotate the PCI cage ha...	35
Figure136. Placing the PCI Cage into the Workstation	35
Figure136. Placing the PCI Cage into the Workstation	35
<GRAPHIC>	35
4. Complete the procedure in the section	35
5. Connect and turn on the power to your system.	35
6. Determine that your I/O cards were replaced successfully by executing this command as	36
PCI Card Guide Replacement	36
PCI Card Guide Replacement	36
1. Locate the front of the card guide slot and the card guide lip. See	36
1. Locate the front of the card guide slot and the card guide lip. See	36
Figure137. Pushing the Card Guide Forward and Down	36
Figure137. Pushing the Card Guide Forward and Down	36
<GRAPHIC>	36
Figure138. Replacing the Card Guide into the PCI Cage Cover	36
Figure138. Replacing the Card Guide into the PCI Cage Cover	36
<GRAPHIC>	37
Removing the Hard Disk Drive(s)	37
1. Complete the procedure in the section	37
1. Complete the procedure in the section	37
2. Complete the procedure in the section	37
3. Grasp the hard disk drive handle and pull it back, then lift up on the handle. See	37
Figure139. Removing the Hard Disk Drive and Its Mounting Bracket	37
Figure139. Removing the Hard Disk Drive and Its Mounting Bracket	37
<GRAPHIC>	37
Figure140. Removing the Hard Disk Drive from the Hard Disk Drive Bracket	37
Figure140. Removing the Hard Disk Drive from the Hard Disk Drive Bracket	37
<GRAPHIC>	38
Replacing the Hard Disk Drive(s)	38
1. Remove the CD drive, DAT drive or flexible disk drive if you have not already done this. Other...	38
1. Remove the CD drive, DAT drive or flexible disk drive if you have not already done this. Other...	38
2. Remove the PCI cage if you have not already done this. Otherwise, skip this step. To remove th...	38
3. Insert the hard disk drive into the hard disk drive bracket and align the holes in the disk dr...	38
Figure141. Installing the Hard Disk Drive into the Hard Disk Drive Bracket	38
Figure141. Installing the Hard Disk Drive into the Hard Disk Drive Bracket	38
<GRAPHIC>	38
Figure142. Replacing the Hard Disk Drive and Bracket in the Workstation	38
Figure142. Replacing the Hard Disk Drive and Bracket in the Workstation	38
<GRAPHIC>	39
6. Complete the procedure in the section	39
7. Complete the procedure in the section	39
8. Connect and turn on the power to your system.	39
9. Determine that your hard disk drive replacement was successful by executing the	39
Removing the Liquid Crystal Display (LCD) Module	40
Removing the Liquid Crystal Display (LCD) Module	40
1. Complete the procedure in the section	40
1. Complete the procedure in the section	40
2. Disconnect the LCD control cable. See	40
Figure143. Disconnecting the LCD Control Cable	40
Figure143. Disconnecting the LCD Control Cable	40
<GRAPHIC>	40
Figure144. Removing the LCD Module	40
Figure144. Removing the LCD Module	40
<GRAPHIC>	41
Replacing the Liquid Crystal Display (LCD) Module	41
1. Remove the front bezel if you have not already done this. Otherwise, skip this step. To remove...	41
1. Remove the front bezel if you have not already done this. Otherwise, skip this step. To remove...	41
2. Replace the LCD Module by inserting the left-side and right-side retainer clips in their slots...	41
Figure145. Replacing the LCD Module	41
Figure145. Replacing the LCD Module	41
<GRAPHIC>	41
Figure146. Connection the LCD Control Cable Connector	41
Figure146. Connection the LCD Control Cable Connector	41
<GRAPHIC>	41
5. Connect and turn on the power to your system.	41
6. Determine that your LCD Module replacement was successful by looking at the LCD and noticing i...	41
Removing the AC or DC Power Supply	42
Removing the AC or DC Power Supply	42
1. Unplug the power cord from the system as stated in the WARNING at the beginning of this chapter.	42
1. Unplug the power cord from the system as stated in the WARNING at the beginning of this chapter.	42
2. Complete the procedure in the section	42
3. Disconnect the power supply cables from the system board by pressing in on the latch releases ...	42
Figure147. Disconnect the Power Supply Cables	42
Figure147. Disconnect the Power Supply Cables	42
<GRAPHIC>	43
Figure148. Unscrewing the Four Power Supply Mounting Screws	43
Figure148. Unscrewing the Four Power Supply Mounting Screws	43
<GRAPHIC>	43
Figure149. Removing the AC Power Supply	43
Figure149. Removing the AC Power Supply	43
<GRAPHIC>	44
Replacing the AC or DC Power Supply	44
1. Remove the AC power supply if you have not already done this. Otherwise, skip this step. To re...	44
1. Remove the AC power supply if you have not already done this. Otherwise, skip this step. To re...	44
2. Replace the AC power supply in the workstation. To do this, you will have to slide the power s...	44
Figure150. Replacing the AC Power Supply	44
Figure150. Replacing the AC Power Supply	44
<GRAPHIC>	44
Figure151. Screwing in the Four Power Supply Mounting Screws	44
Figure151. Screwing in the Four Power Supply Mounting Screws	44
<GRAPHIC>	45
Figure152. Connect the Power Supply Cables	45
Figure152. Connect the Power Supply Cables	45
<GRAPHIC>	45
6. Connect and turn on the power to your system.	45
7. Determine that your AC power supply replacement was successful by observing to see if the work...	45
Removing the System Board	46
Removing the System Board	46
1. Complete the procedure in the section	46
1. Complete the procedure in the section	46
2. Complete the procedure in the section	46
3. Complete the procedure in the section	46
4. Complete the procedure in the section	46
5. Disconnect the two fan power connectors from the system board by pressing in on the latch reta...	46
Figure153. Removing the Internal System Board Mounting Screws	46
Figure153. Removing the Internal System Board Mounting Screws	46
<GRAPHIC>	46
Figure154. Removing the System Boards Rear Mounting Screw	46
Figure154. Removing the System Boards Rear Mounting Screw	46
<GRAPHIC>	47
Figure155. Slide the System Board Off Its Standoffs	47
Figure155. Slide the System Board Off Its Standoffs	47
<GRAPHIC>	47
Figure156. Lifting the System Board Out of the Workstation	47
Figure156. Lifting the System Board Out of the Workstation	47
<GRAPHIC>	48
Replacing the System Board	48
1. Remove the system board if you have not already done this. Otherwise, skip this step. To remov...	48
1. Remove the system board if you have not already done this. Otherwise, skip this step. To remov...	48
2. Use the system board’s turbo-cooler heatsink and handle to place it in the workstation. The sy...	48
Figure157. Placing the System Board in the Workstation	48
Figure157. Placing the System Board in the Workstation	48
<GRAPHIC>	48
Figure158. Sliding the System Board Onto Its Standoffs	48
Figure158. Sliding the System Board Onto Its Standoffs	48
<GRAPHIC>	49
Figure159. Screwing in the System Board’s Rear Mounting Screw	49
Figure159. Screwing in the System Board’s Rear Mounting Screw	49
<GRAPHIC>	49
Figure160. Replacing the Internal System Board Mounting Screws	49
Figure160. Replacing the Internal System Board Mounting Screws	49
<GRAPHIC>	49
7. Complete the procedure in the section	49
8. Complete the procedure in the section	49
9. Complete the procedure in the section	49
10. Complete the procedure in the section	50
11. Connect and turn on the power to your system.	50
12. Determine that your system board replacement was successful by observing to see if the workst...	50
Removing the Fan Modules	51
Removing the Fan Modules	51
<TABLE>	51
Table11. System Area and PCI area Fan Numbers	51
<TABLE HEADING>	51
<TABLE ROW>	51
Fan Number	51
Description	51
<TABLE BODY>	51
<TABLE ROW>	51
1	51
Power Supply Fan	51
<TABLE ROW>	51
2	51
Right System Area Fan (as you face the system’s front)	51
<TABLE ROW>	51
3	51
Left System Area Fan (as you face the system’s front)	51
<TABLE ROW>	51
5	51
Left PCI Area Fan (as you face the system’s front)	51
<TABLE ROW>	51
6	51
Right PCI Area Fan (as you face the system’s front)	51
<TABLE ROW>	51
7	51
CPU’s Turbo-Cooler Heatsink	51
Figure161. System and PCI Fan Areas	51
Figure161. System and PCI Fan Areas	51
<GRAPHIC>	52
System Area Fan Module Removal	52
1. Complete the procedure in the section	52
1. Complete the procedure in the section	52
2. Complete the procedure in the section	52
3. Unscrew the two LCD connector screws and remove the LCD connector from its opening in the chas...	52
Figure162. Removing the LCD Connector	52
Figure162. Removing the LCD Connector	52
<GRAPHIC>	52
Figure163. Disconnecting the Fan-Module Power Cables for the System Area	52
Figure163. Disconnecting the Fan-Module Power Cables for the System Area	52
<GRAPHIC>	53
Figure164. Removing the Fan-Module Mounting Screw	53
Figure164. Removing the Fan-Module Mounting Screw	53
<GRAPHIC>	53
Figure165. Removing the System Area Fan Module	53
Figure165. Removing the System Area Fan Module	53
<GRAPHIC>	54
PCI Area Fan Module Removal	54
1. Complete the procedure in the section	54
1. Complete the procedure in the section	54
2. Complete the procedure in the section	54
3. Disconnect the two fan-module power cables from the system board by pressing in on the latch r...	54
Figure166. Disconnecting the Fan-Module Power Cables	54
Figure166. Disconnecting the Fan-Module Power Cables	54
<GRAPHIC>	54
Figure167. Remove the Fan-Module Mounting Screw for the PCI Area	54
Figure167. Remove the Fan-Module Mounting Screw for the PCI Area	54
<GRAPHIC>	55
Figure168. Removing the PCI Area Fan Module	55
Figure168. Removing the PCI Area Fan Module	55
<GRAPHIC>	56
Replacing the Fan Modules	56
<TABLE>	56
Table12. System Area and PCI area Fan Numbers	56
<TABLE HEADING>	56
<TABLE ROW>	56
Fan Number	56
Description	56
<TABLE BODY>	56
<TABLE ROW>	56
1	56
Power Supply Fan	56
<TABLE ROW>	56
2	56
Right System Area Fan (as you face the system’s front)	56
<TABLE ROW>	56
3	56
Left System Area Fan (as you face the system’s front)	56
<TABLE ROW>	56
5	56
Left PCI Area Fan (as you face the system’s front)	56
<TABLE ROW>	56
6	56
Right PCI Area Fan (as you face the system’s front)	56
<TABLE ROW>	56
7	56
CPU’s Turbo-Cooler Heatsink	56
Figure169. System and PCI Fan Areas	56
Figure169. System and PCI Fan Areas	56
<GRAPHIC>	57
System Area Fan Module Replacement	57
1. Remove the system area fan module if you have not done this. Otherwise, skip this step. To rem...	57
1. Remove the system area fan module if you have not done this. Otherwise, skip this step. To rem...	57
2. Replace the fan module in the workstation by tilting it back away from the workstation chassis...	57
Figure170. Replacing the System Area Fan Module	57
Figure170. Replacing the System Area Fan Module	57
<GRAPHIC>	57
Figure171. Screwing in the Fan-Module Mounting Screw	57
Figure171. Screwing in the Fan-Module Mounting Screw	57
<GRAPHIC>	58
Figure172. Plugging the Fan-Module Power Cables into the System Board	58

Match case Limit results 1 per page

Appendix D

Remove/Replace Flexible Disk Drives

Removing the Flexible Disk Drive

101

8. Unscrew the four bracket mounting screws from the ﬂexible disk drive and remove the ﬂexible

disk drive from its bracket. See

Figure D-7.

Figure D-7

Unscrew the Four Flexible Disk Drive Mounting Screws

Removing the SCSI Cable

Because there are special considerations you should know regarding the removal of the SCSI cable,

this section explains some of those considerations. This section also explains how to remove the

SCSI cable from your workstation’s PCI cage.

Here are some important points to remember regarding the SCSI card and cable.

•

The SCSI card can be installed in any of the unused slots in your workstation’s PCI cage;

however, for ease of cable routing it is best to install your SCSI card in slot 4 of the PCI cage.

•

The SCSI cable is long enough to allow you to run it through the ﬂexible disk drive bay and out

its front. This makes it easy for you to connect your power and SCSI cable connectors to the

ﬂexible disk drive.

•

The connectors on both ends of the SCSI cable are keyed to allow for proper pin connection.

However, the ﬂexible disk drive’s connector is

not keyed

and you have to align the red line on

the SCSI cable with the left side (as viewed from the back of the ﬂexible disk drive) of the ﬂexible

disk drive’s SCSI connector.

To remove the SCSI card and cable, follow this procedure:

Complete the procedure in the section

“Removing the Flexible Disk Drive”

found in this

appendix.

Bracket Mounting Screws

Flexible Disk Drive

Bracket

Flexible Disk Drive