HP dx2100 HP Compaq dx2100 MT Series PC Service Reference Card, 1st Edition - Page 1
HP dx2100 - Microtower PC Manual
View all HP dx2100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Service Reference Card HP Compaq dx2100 MT Series Business PC © 2005 Hewlett-Packard Development Company, L.P. The informa- tion contained herein is subject to change without notice. HP shall not be liable for technical or editorial errors or omissions contained herein. Intel, Pentium, Intel Inside, and the Intel logo are trademarks or registered trademarks of the Intel Corporation and its subsidiaries in the U. S. and other countries. Document Number 404568-001. 1st Edition November 2005. Key Specifications Processor Type: Intel Celeron D or Pentium 4 RAM Type: DDR PC2 4200, non-ECC Maximum RAM Supported: 4 GB Expansion Bus: PCI 2.2 Graphics Adapter Integrated controller. PCI-e support. Hard drive interface: SATA 1.5 Gb/s I/O Interfaces: Serial (1), parallel (1), USB 2.0 (6), diskette drive (1) System Setup and Boot Basic system information regarding system information, setup, power management, hardware, and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence. If the screen prompt opportunity is missed, a restart will be necessary. Computer Setup Menu Heading System Information Standard CMOS Setup Advanced BIOS Features Option / Description Lists the following main system specifications: • Product Name • SKU number • Processor Type • Processor Speed • CPU ID • Cache Size • Memory Size • System ROM • Integrated MAC Address • UUID • System serial number • Asset tag number Date (mm/dd/yy) - Allows you to set system date. Time (hh:mm:ss) - Allows you to set system time. PATA Controller - Disables/enables PATA controller PATA Ch 0 Master/PATA Ch 0 Slave - Allows you to detect IDE HDD size in selected channel, set UIDE on selected channel, set access mode on selected channel, view firmware version, and capacities, run SMART HDD status, and perform various SMART tests. SATA Controller - Disables/enables controller and both SATA and PATA channels. PATA IDE Mode - Allows you to identify if the PATA device is for the primary or secondary channel. SATA Port - Displays the SATA Port settings. PATA Ch 0 Master/PATA Ch 1 Master - Allows you to detect HDD size in selected channel, set extended drive on selected channel, set access mode on selected channel, view firmware version, and capacities, run SMART HDD status, and perform various SMART tests. Floppy Controller - Disables/enables floppy drive controller. Drive A - allows you to set floppy drive to None or 1.44, 3.5 in. Halt On - Allows you to set POST error behavior. POST Delay - Allows you to set a POST delay to 1, 5, 10, 15, or 30 seconds. Device Boot Disabling - Allows you to restrict a device from booting. Removable Device Boot Priority - Allows you to specify the order of attached removable devices in the boot sequence. Hard Disk Boot Priority - Allows you to specify the order in which attached HDDs are booted. Optical Drive Boot Priority - Allows you to specify the order in which attached ODDs are checked for a bootable operating system image. Network Boot priority - Allows you to specify the order in which network devices are checked for a bootable OS image. F9 Boot Menu Display - Disables/enables Boot menu. Quick Power On Self Test - Disables/enables system to skip select tests while booting. First, Second, or Third Boot Device - Allows you to specify boot sequence or disable any of the three devices. HDD S.M.A.R.T. Capability - Disables/enables S.M.A.R.T. Capability Boot up Numlock Status - Allows you to turn the default feature on or off. Security Option - Allows you to set security to determine whether a password is needed for booting or when entering Computer Setup. Hyper-Threading Technology - Disables/enables hyper-threading if the OCS permits it. APIC Mode - Disables/enables APIC. MPS Version Control for OS - Allows you to select 1.1 or 1.4 MPS table version. OS Select for DRAM > 64MB -Allows you to select OS2 or Non-OS2. Use OS2 only when RAM is greater than 64 MB. BIOS write Protection - Disables/enables ROM BIOS upgrading. Computer Setup Menu (Continued) Heading Option / Description Advanced PCI Express Root Port Func - Allows you to set PCI Express Port 1 Chipset Fea- Auto, Enabled, or disabled and also to set PCI-e Compliance Mode to tures either v1.0 or 1.0a. On-Chip Frame Buffer Size (VGA Setting) - Allows you to set buffer size to 1MB or 8 MB. DVMT Mode (VGA Setting) - Allows you to set mode to Fixed, DVMT, or Both. DVMT /Fixed Memory Size (VGA Setting) - Allows you to set memory size to 64MB or 128 MB. Init Display First (VGA Setting) - Allows you to set initial clock detection to PCI slot or Onboard. Auto Detect PCI Clk - Disables/enables PCI clock auto detection. Spread Spectrum - Disables/enables clock spread spectrum. Integrated USB Controller - Disables/enables USB controller. Peripherals USB Legacy Support - Disables/enables USB keyboard and mouse. Onboard Audio - Allows you to auto-detect or disable onboard audio. Onboard LAN - Disables/enables onboard LAN controller. Onboard LAN Boot ROM- Disables/enables Boot ROM onboard on the LAN chip. Onboard Serial Port 1 - Allows you to select one of these settings: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, or 2E8/IRQ3. Onboard Parallel Port - Allows you to select one of these settings: Disabled, 378/IRQ7, 278/IRQ5, or 3BC/IRQ7. Parallel Port Mode - Allows you to set parallel port mode to SPP, EPP, ECP, or ECP+EPP. ECP Mode use DMA - If parallel port mode set to ECP or ECP+EPP, allows you to set DMA channel for ECP mode to 1 or 3. Power Management Setup ACPI Function - Disables/enables ACPI functions. Changing this can make the installed OS unusable. ACPI Suspend Type - Allows you to set ACPI suspend to S1 (POS), S3 (STR) or S1 & S3. Soft off by Power Button - Allows you to set power button to instant off or 4 second delay. Power On After Power-Fail - Allows you to select system power loss behavior to Last state, On, or Off. MODEM use IRQ - Allows you to set IRQ for modem to NA (disable), 3, 4, 5, 7, 9, 10, or 11. Resume by PME - Disables/enable the feature. Wake on Device S5 - Disables/enables wake device from network. Resume by Alarm - Disables/enables RTC alarm. Date (of Month) Alarm - If resume by Alarm is enabled, allows you to select the day of the month to resume RTC alarm. Time (hh:mm:ss) Alarm - Allows you to set the time the RTC alarm will resume if the Resume by Alarm feature is enabled. PnP/PCI Configurations Allows you to select whether resources are controlled automatically or manually. IRQ Resources - When resources are manually controlled, allows you to assign a type to each system interrupt based on the device using it. Maximum Payload Size - Allows you to set TLP payload size for the PCI-e devices to 128, 256, 512, 1024, 2048, or 4096 bytes. PC Health Status CPU Temperature - View. CPU Fan Speed - View. System Fan Speed - View. SYS Fan Fault Check - Disable/enable detection of fan failure during POST. Load Optimized Defaults Allows you to reset Computer Setup to factory defaults. Set Supervi- Allows you to set a password to control access to Computer Setup. sor Password Set User Password Allows you to set a password to control access to the Computer. Save & Exit Allows you to save current settings and exit Computer Setup. Setup Exit With- Allows you to exit Computer Setup without saving changes. out Saving