HP t510 Troubleshooting Guide t510 Thin Client - Page 31

Setup Utility—Power Management Setup, Setup Utility—Utility Task Actions

Get HP t510 PDF manuals and user guides View all HP t510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Setup Utility-Power Management Setup Table 3-6 Setup Utility-Power Management Setup Option PWRON After PWRFail Wake on PME BIOS Wake up Day of Week Time of Day Eup Lot6 Description When power is lost and comes back, the option determines what power state the system should go to. Options are Off, On, and Former-Sts. Default is Former-Sts. Enable/disable system wakeup capability for OnBoard LAN device and PCI card. Default is enabled. Enable RTC alarm wakeup. Default is disabled. Select the alarm RTC wakeup day of Sunday through Saturday. Select the alarm RTC wakeup time of day (hh:mm). Enable or disable EuP (Energy Using Product) Lot6 power consumption mode. Default is disabled. Setup Utility-Utility Task Actions Table 3-7 Setup (F10) Utility Task Actions Heading Load Factory Defaults Table Select Yes or No (Y/N) Set Administrator Password Allows you to set, change, and disable the administrator password. Set User Password Allows you to set, change, and disable the user password. NOTE: When the user password is set, it prevents unauthorized access to the user's setup. User password provides read-only access to Setup options. Save & Exit Setup Saves data to CMOS, then exit the Setup Utility. Exit without Saving Exit the Setup Utility without saving any changes. Using the BIOS Settings 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Setup Utility—Power Management Setup
Table 3-6
Setup Utility—Power Management Setup
Option
Description
PWRON After PWR-
Fail
When power is lost and comes back, the option determines what power state the system should
go to. Options are Off, On, and Former-Sts. Default is Former-Sts.
Wake on PME
Enable/disable system wakeup capability for OnBoard LAN device and PCI card. Default is
enabled.
BIOS Wake up
Enable RTC alarm wakeup. Default is disabled.
Day of Week
Select the alarm RTC wakeup day of Sunday through Saturday.
Time of Day
Select the alarm RTC wakeup time of day (hh:mm).
Eup Lot6
Enable or disable EuP (Energy Using Product) Lot6 power consumption mode. Default is
disabled.
Setup Utility—Utility Task Actions
Table 3-7
Setup (F10) Utility Task Actions
Heading
Table
Load Factory Defaults
Select Yes or No (
Y
/
N
)
Set Administrator Password
Allows you to set, change, and disable the administrator password.
Set User Password
Allows you to set, change, and disable the user password.
NOTE:
When the user password is set, it prevents unauthorized access to the user's
setup. User password provides read-only access to Setup options.
Save & Exit Setup
Saves data to CMOS, then exit the Setup Utility.
Exit without Saving
Exit the Setup Utility without saving any changes.
Using the BIOS Settings
23