Hikvision DS-2CD2085FWD-I Quick Start Guide - Page 5

Safety Instruction

Get Hikvision DS-2CD2085FWD-I PDF manuals and user guides View all Hikvision DS-2CD2085FWD-I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. ngs are Transportation Keep the device in original or similar packaging while transporting it. any of Power Supply material The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low Voltage) and the Limited Power Source. Refer to the appropriate documentation for detailed information. The standard power supply is 12 VDC, PoE (802.3at) or Hi-PoE, please make sure your power supply matches with your camera. DO NOT connect multiple devices to one power adapter, to avoid overheating or fire hazards caused by overload. Make sure the plug is properly connected to the power socket. System Security The installer and user are responsible for password and security configuration and its settings. Battery Improper use or replacement of the battery may result in explosion hazard. Replace with the same or equivalent type only. Dispose of used batteries in conformance with the local codes. Maintenance If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details. Cleaning Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do not use alkaline detergents. Using Environment When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out. Do not expose the device to high electromagnetic radiation or dusty environments. For indoor-only device, place it in a dry and well-ventilated environment. Do not aim the lens at the sun or any other bright light.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
Safety Instruction
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
The device should be used in compliance with local laws,
electrical
safety regulations, and fire prevention regulations.
Transportation
Keep the device in original or similar packaging while transporting it.
Power Supply
The input voltage should conform to IEC60950-1 standard: SELV
(Safety Extra Low Voltage) and the Limited Power Source. Refer to the
appropriate documentation for detailed information.
The standard power supply is 12 VDC, PoE (802.3at) or Hi-PoE, please
make sure your power supply matches with your camera.
DO NOT connect multiple devices to one power adapter, to avoid over-
heating or fire hazards caused by overload.
Make sure the plug is properly connected to the power socket.
System Security
The installer and user are responsible for password and security
configuration and its settings.
Battery
Improper use or replacement of the battery may result in explosion
hazard. Replace with the same or equivalent type only. Dispose of used
batteries in conformance with the local codes.
Maintenance
If the product does not work properly, please contact your dealer or
the nearest service center. We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular
replacement. The average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside surfaces
of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device lens is
not exposed to the laser beam, or it may burn out.
Do not expose the device to high electromagnetic radiation or dusty
environments.
For indoor-only device, place it in a dry and well-ventilated environment.
Do not aim the lens at the sun or any other bright light.
e
f
l