Hikvision DS-2CD2085FWD-I Quick Start Guide - Page 6

Mark Description

Get Hikvision DS-2CD2085FWD-I PDF manuals and user guides View all Hikvision DS-2CD2085FWD-I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Make sure the running environment meets the requirement of the device. The operating humidity shall be 95% or less (non- condensing), and the operating temperature is below: Indoor device: -10°C to 40 °C (14 °F to 104 °F ), Outdoor device: -30 °C to 60 °C (-22 °F to 140 °F), or -H model: -40 °C to 60 °C (-40 °F to 140 °F). Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. IR Reflection Prevention Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly. Emergency If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center. Time Synchronization Set up camera time manually for the first time access if the local time is not synchronized with that of the network. Visit the camera via Web browse/client software and go to time settings interface. Installation Make sure the device is firmly secured to any wall or ceiling mountings. Be sure that there is enough space to install the camera and accessories. Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that the wall is strong enough to withstand at least 4 times the weight of the camera and the mount. Make sure that the power has been disconnected before you wire, install, or disassemble the device. Mark Description Mark Description Read this manual before using the product.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
Make sure the running environment meets the requirement of the
device. The operating humidity shall be 95% or less (non- condensing),
and the operating temperature is below:
Indoor device: -10°C to 40 °C (14 °F
to 104 °F ),
Outdoor device: -30 °C to 60 °C (-22 °F to 140 °F), or -H model: -40 °C
to 60 °C (-40 °F to 140 °F).
Do not place the camera in extremely hot, cold, dusty or damp locations,
and do not expose it to high electromagnetic radiation.
IR Reflection Prevention
Dust or grease on the dome cover will cause IR reflection. Please do
not remove the dome cover film until the installation is finished. If there
is dust or grease on the dome cover, clean the dome cover with clean
soft cloth and isopropyl alcohol.
Make sure that there is no reflective surface too close to the camera
lens. The IR light from the camera may reflect back into the lens causing
reflection.
The foam ring around the lens must be seated flush against the inner
surface of the bubble to isolate the lens from the IR LEDS. Fasten the
dome cover to camera body so that the foam ring and the dome cover
are attached seamlessly.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the
power, unplug the power cable, and contact the service center.
Time Synchronization
Set up camera time manually for the first time access if the local time
is not synchronized with that of the network. Visit the camera via Web
browse/client software and go to time settings interface.
Installation
Make sure the device is firmly secured to any wall or ceiling mountings.
Be sure that there is enough space to install the camera and
accessories.
Make sure that the device in the package is in good condition and all the
assembly parts are included.
Make sure that the wall is strong enough to withstand at least 4 times
the weight of the camera and the mount.
Make sure that the power has been disconnected before you wire,
install, or disassemble the device.
Mark Description
Mark
Description
Read this manual before using the product.