Hikvision DS-2CD2T25FWD-I5 User Manual - Page 106

Configuring Video Tampering Alarm, Scheduled-Switch, Switch Day and Night Settings

Get Hikvision DS-2CD2T25FWD-I5 PDF manuals and user guides View all Hikvision DS-2CD2T25FWD-I5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Network Camera User Manual 6. Set the arming schedule and linkage method as in the normal configuration mode. 7. Click Save to save the settings.  Day/Night Scheduled-Switch Steps: 1. Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. 2. Select Scheduled-Switch for Switch Day and Night Settings. Figure 10-6 Day/Night Scheduled-Switch 3. Select the start time and the end time for the switch timing. 4. Select the area by clicking the area No.. 5. Slide the cursor to adjust the sensitivity and proportion of object on the area for the selected area in the daytime. 6. Slide the cursor to adjust the sensitivity and proportion of object on the area for the selected area at night. 7. Set the arming schedule and linkage method as in the normal configuration mode. 8. Click Save to save the settings. 10.1.2 Configuring Video Tampering Alarm Purpose: You can configure the camera to trigger the alarm when the lens is covered and take certain alarm response actions. Detection area for this alarm is the whole screen. Steps: 1. Enter the video tampering Settings interface, Configuration > Event > Basic Event > Video Tampering. 96

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Network Camera User Manual
96
6.
Set the arming schedule and linkage method as in the normal configuration mode.
7.
Click
Save
to save the settings.
Day/Night Scheduled-Switch
Steps:
1.
Draw the detection area as in the normal configuration mode. Up to 8 areas are
supported.
2.
Select
Scheduled-Switch
for
Switch Day and Night Settings
.
Day/Night Scheduled-Switch
Figure 10-6
3.
Select the start time and the end time for the switch timing.
4.
Select the area by clicking the area No..
5.
Slide the cursor to adjust the sensitivity and proportion of object on the area for
the selected area in the daytime.
6.
Slide the cursor to adjust the sensitivity and proportion of object on the area for
the selected area at night.
7.
Set the arming schedule and linkage method as in the normal configuration mode.
8.
Click
Save
to save the settings.
10.1.2
Configuring Video Tampering Alarm
Purpose:
You can configure the camera to trigger the alarm when the lens is covered and take
certain alarm response actions.
Detection area for this alarm is the whole screen.
Steps:
1.
Enter the video tampering Settings interface,
Configuration > Event > Basic
Event > Video Tampering
.