Hitachi 50VS69 Owners Guide - Page 38

Channel Manager

Get Hitachi 50VS69 - UltraVision VS69 Series PDF manuals and user guides View all Hitachi 50VS69 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Channel Manager Channel Manager Select CHANNEL MANAGER to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. 1. Press CURSOR PAD ̆, ̄ or CHANNEL UP/DOWN buttons to highlight function. Video Audio Channel Manager Locks Timers Setup Move SEL Select 2. Press the SELECT button or CURSOR PAD ̈ to select. Channel Manager Signal Meter OR Auto Channel Scan Channel List Move SEL Select On-Screen Display Signal Meter Select SIGNAL METER when using an indoor or outdoor antenna. This feature will show the signal strength and OR peak values of the Antenna signal to help you adjust your antenna to optimize signal reception. Use the CURSOR PADS and the SELECT button to highlight and select CLOSE to exit. NOTE: The Signal Meter will not be available (grayed out) when watching analog channels. Channel Manager Signal Meter Auto Channel Scan Channel List Move SEL Select Channel Manager Signal Meter Channel 3-1 Strength 91 Peak 91 SNR 10 Close Move SEL Return Auto Channel Scan This feature will automatically store active Analog and Digital channels in Auto Channel Scan memory. 1. Use the CURSOR buttons ̇ or ̈ to highlight AIR, CABLE (1) or CABLE(2) source. 2. Press the CURSOR buttons ̇ or ̈ to highlight the START or RESET option. 3. Press the SELECT button to select. NOTE: 1. When a CableCARD is installed, Auto OR Channel Scan will not be available since channels will be fixed based on what was agreed upon by you and your cable operator. 2. If certain channels are poor or not possible in cable(1) mode, set cable source to cable(2) by using the CURSOR buttons ̇ or ̈. 38 Channel Manager Signal Meter Auto Channel Scan Channel List Move SEL Select Channel Manager Auto Channel Sc an Source Air Auto Channel Scan Start Reset Move SEL R eturn

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
On-Screen Display
Channel Manager
Select
CHANNEL MANAGER
to set your Antenna
options, run Auto Channel Scan, Check Signal Meter
and Set Channel List.
1.
Press CURSOR PAD
²
,
±
or CHANNEL
UP/DOWN
buttons to
highlight function
.
2.
Press the SELECT button or CURSOR PAD
´
to
select.
Signal Meter
Select
SIGNAL METER
when using an indoor or outdoor
antenna. This feature will show the signal strength and
peak values of the Antenna signal to help you adjust your
antenna to optimize signal reception.
Use the
CURSOR PADS
and the
SELECT
button to
highlight and select
CLOSE
to exit.
NOTE:
The Signal Meter will not be available (grayed
out) when watching analog channels.
Auto Channel Scan
This feature will automatically store active Analog and
Digital channels in Auto Channel Scan memory.
Channel Manager
Setup
Timers
Locks
Channel Manager
Audio
Video
Move
SEL
Select
Channel List
Auto Channel Scan
Signal Meter
Channel Manager
Move
SEL
Select
Channel List
Auto Channel Scan
Signal Meter
Channel Manager
Move
SEL
Select
Signal Meter
Channel Manager
Move
SEL
Return
Channel
3-
1
Strength
9
1
Peak
9
1
SNR
10
Channel List
Auto Channel Scan
Signal Meter
Channel Manager
Move
SEL
Select
OR
OR
Close
1.
Use the
CURSOR
buttons
to highlight
AIR, CABLE (1) or CABLE(2) source.
2.
Press the
CURSOR
buttons
³
or
´
to highlight the
START
or
RESET
option.
3.
Press the
SELECT
button to select.
³
or
´
NOTE:
1.
When a CableCARD is installed, Auto
Channel Scan will not be available since
channels will be fixed based on what was
agreed upon by you and your cable
operator.
2.
If certain channels are poor or not possible
in cable(1) mode, set cable source to cable(2)
by using the CURSOR buttons
³
or
´
.
OR
Auto Channel Scan
Channel Manager
Move
SEL
R eturn
Source
Air
Auto Channel Scan
Start
Reset
38