Hitachi CP-X3010 Operation Guide

Hitachi CP-X3010 - XGA LCD Projector Manual

Get Hitachi CP-X3010 - XGA LCD Projector PDF manuals and user guides
UPC - 050585151703
View all Hitachi CP-X3010 manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CP-X3010 manual content summary:

  • Hitachi CP-X3010 | Operation Guide - Page 1
    Projector CP-X2010/CP-X2510/CP-X3010 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read "Safety Guide" first. After reading them, store them in a safe place for future
  • Hitachi CP-X3010 | Operation Guide - Page 2
    Maintenance 53 Adjusting the position 19 Replacing the lamp 53 Correcting the keystone distortions. . . 20 Cleaning and replacing the air filter . . 55 Using the magnify feature 20 Other care 57 Temporary freezing the screen. . . . . 21 Troubleshooting 58 Temporarily blanking the screen
  • Hitachi CP-X3010 | Operation Guide - Page 3
    Remote control with two AA batteries (2) Power cord (3) Computer cable (4) Lens cover (2) (6) (5) User's manuals (Book x1, CD x1) (3) (6) Security label NOTE • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector
  • Hitachi CP-X3010 | Operation Guide - Page 4
    Part names Projector (1) Lamp cover (&53) The lamp unit is inside. (2) Focus ring (&18) (3) Zoom ring (&18) (4) Control panel (&5) (5) Elevator buttons (x 2) (&18) (6) Elevator feet (x 2) (&18) (7) Remote sensor (&12) (8) Lens (&57) (9) Intake vents (10) F ilter cover (&55) The air filter and
  • Hitachi CP-X3010 | Operation Guide - Page 5
    POWER indicator (&11, 14, 59) (5) TEMP indicator (&59) (6) LAMP indicator (&59) Rear panel (&9) (1) AUDIO IN1 port (2) AUDIO IN2 port (3) COMPUTER IN1 port (4) COMPUTER IN2 port (5) MONITOR OUT port (6) Shutdown switch (&60) (7) CONTROL switch only when the projector is not turned off by normal
  • Hitachi CP-X3010 | Operation Guide - Page 6
    Part names Remote control (1) VIDEO button (&16) (2) COMPUTER button (&16) (2) (1) (3) SEARCH button (&17) (6) (4) STANDBY/ON button (&14) (5) (5) ASPECT button (&17) (6) AUTO button (&19) RESET (10) (4) (3) (7) (12) (14) (11) (13) (15) (18) (21) (23) (25) (26) Back of the remote control 6
  • Hitachi CP-X3010 | Operation Guide - Page 7
    cm or more between the sides of the projector and other objects such as walls. • For the case of installation in a special state such as ceiling mount, the specified mounting accessories (&64) and service may be required. Before installing the projector, consult your dealer about your installation
  • Hitachi CP-X3010 | Operation Guide - Page 8
    , and leave installing and removing the projector with the mounting accessories to the service personnel. • Read and keep the user's manual of the mounting accessories used. CAUTION ►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause fire
  • Hitachi CP-X3010 | Operation Guide - Page 9
    the manuals for devices before connecting them to the projector. ௥ power cords prior to connecting them to projector. Connecting a live device to the projector may projector. ►Use appropriate accessory or designated cables. Ask your dealer about nonaccessory cables which may be required a specific
  • Hitachi CP-X3010 | Operation Guide - Page 10
    projector, be sure to activate the PC's external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual other CRT or LCD monitors to change the resolution. • In some cases, this projector may not
  • Hitachi CP-X3010 | Operation Guide - Page 11
    electrical shock. • Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one. • Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the
  • Hitachi CP-X3010 | Operation Guide - Page 12
    hook part of the battery cover, remove it. 1 2 3 2. Align and insert the two AA batteries (HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. 3. Replace the battery cover in the direction of the arrow and snap it back into place
  • Hitachi CP-X3010 | Operation Guide - Page 13
    REMOTE FREQ. in the SERVICE item of the OPTION menu (46) of the projector to be controlled should be set to the same mode as the remote control check your PC's manuals before connecting this product projector is working properly. This function is not available while the lamp is warming up (the POWER
  • Hitachi CP-X3010 | Operation Guide - Page 14
    indicator is steady orange (59). Then remove the lens cover. 3. Press STANDBY/ON button on the projector or the remote control. The projection lamp will light up and POWER MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME UP ON 㧗 DOWN OFF ࡯ KEYSTONE
  • Hitachi CP-X3010 | Operation Guide - Page 15
    MENU ● When the projector is in the standby mode, the volume can be ENTER adjusted if is not selected for the AUDIO OUT STANDBY and NOESRC MAL isRESET selected to the STANDBY MODE in the SETUP menu (35). Temporarily muting the sound 1. Press MUTE button on the remote control. A dialog will
  • Hitachi CP-X3010 | Operation Guide - Page 16
    IN1 port first. DOWN OFF ࡯ KEYSTONE MY BUTTON MUTE 1 2 POSITION MENU ESC ENTER RESET 1. Press VIDEO button on the remote control. Each time you press the button, the projector switches its input port from the current port as below. COMPONENT (Y, Cb/Pb, Cr/Pr)  S-VIDEO  VIDEO ● While
  • Hitachi CP-X3010 | Operation Guide - Page 17
    in above order repeatedly till an input signal is detected. Selecting an aspect ratio 1. Press ASPECT button on the remote control. Each time you press the button, the projector switches the mode for aspect ratio in turn.  F or a computer signal NORMAL  4:3  16:9  16:10  F or a video signal
  • Hitachi CP-X3010 | Operation Guide - Page 18
    the elevator feet. 4. After making sure that the elevator feet are locked, put the projector down gently. 5. If necessary, the elevator feet can be manually twisted to make more precise adjustments. Hold the projector when twisting the feet. 1 5 To loose an elevator foot, push the elevator button
  • Hitachi CP-X3010 | Operation Guide - Page 19
    or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (45).MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK Adjusting the position 1. Press POSITION button on the remote control when no menu is indicated. The "POSITION" indication will
  • Hitachi CP-X3010 | Operation Guide - Page 20
    vertical keystone correction. (2) MANUAL displays a dialog for keystone correction selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, RESET button of MAGNIFY on the remote control. ● The projector automatically exits from the MAGNIFY mode
  • Hitachi CP-X3010 | Operation Guide - Page 21
    long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long. ● Images might appear degraded when this function is operated, but it is not a malfunction. Temporarily blanking the screen 1. Press BLANK button on the remote control. The BLANK
  • Hitachi CP-X3010 | Operation Guide - Page 22
    projector has the following menus: MY SOURCE/ VIDEO COMPUTER DOC.CAMERA PICTURE, IMAGE, INPUT, SETUP to appear just after powered on. While the projector is displaying any menu, the MENU button on the projector works as the instructed in the OSD to operate the item. (continued on next page) 22
  • Hitachi CP-X3010 | Operation Guide - Page 23
    ) cannot be reset. ● In the ADVANCED MENU, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control. Indication in OSD (On Screen Display) The meanings of the general words on the OSD are as follows. Indication EXIT RETURN CANCEL or NO OK
  • Hitachi CP-X3010 | Operation Guide - Page 24
    menu (34). KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion. See the KEYSTONE item in SETUP menu (34). Using the ◄/► buttons switches the picture mode. The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to
  • Hitachi CP-X3010 | Operation Guide - Page 25
    (34). MIRROR Using the ◄/► buttons switches the mode for mirror status. See the MIRROR item in SETUP menu (35). RESET Performing this item resets all of the EASY MENU items except the FILTER TIME and LANGUAGE. A dialog is displayed for confirmation. Selecting the OK using the ► button performs
  • Hitachi CP-X3010 | Operation Guide - Page 26
    from left end on the test pattern, use the equalizing adjustment bar "1". The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar. • Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction
  • Hitachi CP-X3010 | Operation Guide - Page 27
    PICTURE menu Item Description Using the ▲/▼ buttons switches the color temperature mode. 1 HIGH  1 CUSTOM  2 MID  2 CUSTOM 6 CUSTOM 3 LOW 6 Hi-BRIGHT-3 3 CUSTOM COLOR TEMP COLOR TINT SHARPNESS 5 CUSTOM  5 Hi-BRIGHT-2  4 CUSTOM  4 Hi-BRIGHT-1 To adjust CUSTOM Selecting a mode whose
  • Hitachi CP-X3010 | Operation Guide - Page 28
    item is available only for CP-X2510 or CP-X3010. Using the ▲/▼ cursor buttons changes the active iris control mode. PRESENTATION ó THEATER the PRESENTATION or THEATER modes are selected. If this occurs select OFF. This projector has 4 memories for adjustment data (for all the items of the PICTURE
  • Hitachi CP-X3010 | Operation Guide - Page 29
    and component video signal. • When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small. Using the ◄/► buttons adjusts the vertical position. Down ó Up • Over-adjusting the vertical position may cause noise to appear on
  • Hitachi CP-X3010 | Operation Guide - Page 30
    be displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation. • Images might be displayed on the edge of the screen, depending on the PC model. • The items adjusted by this function may vary when the FINE or DISABLE is
  • Hitachi CP-X3010 | Operation Guide - Page 31
    the optimum mode. • The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO. Using the ▲/▼ buttons switches the required for a SCART RGB input to the projector. For details, contact your dealer. (continued on next page) 31
  • Hitachi CP-X3010 | Operation Guide - Page 32
    input a sync on G signal or component signal from the port. • In the AUTO mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and select the SYNC ON G OFF, and then reconnect the signal. Set the frame lock
  • Hitachi CP-X3010 | Operation Guide - Page 33
    COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ vertical (VERT) resolutions using CUSTOM ↓ the buttons. This function is may not support all resolutions. (5) Move the cursor to OK on screen and press the ►
  • Hitachi CP-X3010 | Operation Guide - Page 34
    among inputs. For some input, this function may not work well. • When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly. • When the zoom adjustment is set to the TELE (telephoto focus
  • Hitachi CP-X3010 | Operation Guide - Page 35
    ó NORMAL When SAVING is selected, the power consumption in the standby mode is lowered with some functional restriction as below: STANDBY MODE • When SAVING is selected, the RS-232C communication control is disabled except to turn the projector on while the projector is in the standby mode. • When
  • Hitachi CP-X3010 | Operation Guide - Page 36
    AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table. Item VOLUME SPEAKER AUDIO SOURCE
  • Hitachi CP-X3010 | Operation Guide - Page 37
    or INPUT button to save the language setting. Using the buttons adjusts the menu position. To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds. Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for the
  • Hitachi CP-X3010 | Operation Guide - Page 38
    when the image is displayed. The image will freeze and the frame for capturing will appear. To stop performing, press the RESET button on the remote control. 2. U sing the buttons adjusts the frame position. Please move the frame to the position of the image which you want to use. The frame may
  • Hitachi CP-X3010 | Operation Guide - Page 39
    SCREEN menu Item MyScreen Lock MESSAGE Description Using the ▲/▼ buttons turns on/off the MyScreen lock function. ON ó OFF When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the
  • Hitachi CP-X3010 | Operation Guide - Page 40
    SCREEN menu Item SOURCE NAME TEMPLATE Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE
  • Hitachi CP-X3010 | Operation Guide - Page 41
    video source supporting C.C. feature to utilize this function. It may not work properly, depending on equipment or signal source. In this case, please turn which is for additional information such as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C.
  • Hitachi CP-X3010 | Operation Guide - Page 42
    the usual procedure (14), only when the projector is supplied with the power after the power was cut while the lamp was on. • This function does not work as long as the power has been supplied to the projector while the lamp is off. • After turning the lamp on by the DIRECT ON function, if neither
  • Hitachi CP-X3010 | Operation Guide - Page 43
    about the lamp. • For the lamp replacement, see the section "Replacing the lamp" (53, 54). The filter time is the usage time of the air filter, counted after the last resetting. It is shown in the OPTION menu. Pressing the RESET button on the remote control or the ► button of the projector displays
  • Hitachi CP-X3010 | Operation Guide - Page 44
    remote control (6). (1)Use the ▲/▼ buttons on the MY BUTTON menu to select a MY BUTTON - (1/2) and press the ► button to display the MY BUTTON setup only for CP-X2510 or CP-X3010.) • PICTURE MODE: Changes the PICTURE MODE (24). • F ILTER RESET: Displays the filter time reset confirmation
  • Hitachi CP-X3010 | Operation Guide - Page 45
    the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. FAN SPEED Using the ▲/▼ buttons switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is
  • Hitachi CP-X3010 | Operation Guide - Page 46
    not have any effect on the remote control. REMOTE FREQ. (1)Use the ▲/▼ button to change the projector's remote sensor frequency setting (4). 1:NORMAL ó 2:HIGH (2)Use the ◄/► button to change the projector's remote sensor on or off. ON ó OFF SERVICE (continued) The factory default setting is
  • Hitachi CP-X3010 | Operation Guide - Page 47
    projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User during this time. Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box. • Please do not
  • Hitachi CP-X3010 | Operation Guide - Page 48
    of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu. When a password is set Code. Your password will be sent after your user registration information is confirmed. (continued on next page) 48
  • Hitachi CP-X3010 | Operation Guide - Page 49
    code box is displayed. This function will activate only when the projector is started after AC power is turned off. • Please do not forget your PIN code. the projector will turn off. 3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN Code will be sent after your user registration
  • Hitachi CP-X3010 | Operation Guide - Page 50
    Pressing the ENTER button on the remote control or the ► button on the projector will return to the TRANSITION projector is started after turning off the AC power. • This feature may not function properly if the projector user registration information is confirmed. 50 (continued on next page)
  • Hitachi CP-X3010 | Operation Guide - Page 51
    note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu. 2 Turning off the Your password will be sent after your user registration information is confirmed. (continued on next page) 51
  • Hitachi CP-X3010 | Operation Guide - Page 52
    When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen. • This function is available only when the MY TEXT PASSWORD function is set to the OFF. MY TEXT WRITING (1) Use the ▲/▼ buttons
  • Hitachi CP-X3010 | Operation Guide - Page 53
    : DT01021 Replacing the lamp lamp cover 3 1. Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes. 2. Prepare a new lamp. If the projector is mounted on a ceiling, or if the lamp has broken, also ask the dealer to replace the lamp. In case of
  • Hitachi CP-X3010 | Operation Guide - Page 54
    gas that from the comes out of the projector vents, or get it in your eyes or mouth. power • Before replacing the lamp, turn the projector off and unplug the power outlet cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as
  • Hitachi CP-X3010 | Operation Guide - Page 55
    will come together with a replacement lamp for this projector. 1. Turn the projector off, and unplug the power cord. Allow the projector to sufficiently cool down. Filter cover 2 2. Use a vacuum cleaner on and around the filter cover. 3. While supporting the projector with one hand, use your
  • Hitachi CP-X3010 | Operation Guide - Page 56
    or too soiled. • When you replace the projection lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector. • Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about
  • Hitachi CP-X3010 | Operation Guide - Page 57
    not touch the lens directly with your hand. Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration, peeling paint, etc. 1. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. 2. After making sure that the
  • Hitachi CP-X3010 | Operation Guide - Page 58
    please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH. A note of precaution when cleaning the air filter. Please immediately turn the power off, and clean or change the air filter referring to the "Cleaning and replacing the air filter" section of this manual. After you have cleaned or
  • Hitachi CP-X3010 | Operation Guide - Page 59
    displayed after the remedy, please change the lamp referring to the section "Replacing the lamp". Blinking In Red or Lighting In Red Blinking In Red Turned off The lamp cover has not been properly fixed. Please turn the power off, and allow the projector to cool down at least 45 minutes. After
  • Hitachi CP-X3010 | Operation Guide - Page 60
    FAN SPEED of SERVICE item in OPTION menu to HIGH (45). Lighting In Green Simultaneous blinking in Red It is time to clean the air filter. Please immediately turn the power off, and clean or change the air filter referring to the section "Cleaning and replacing the air filter". After cleaning or
  • Hitachi CP-X3010 | Operation Guide - Page 61
    cool down at least 10 minutes, then turn the power on again. Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. After the
  • Hitachi CP-X3010 | Operation Guide - Page 62
    . 26 The computer cannot detect the projector as a plug and play monitor. Make sure that the computer can detect a plug and play 10 monitor using another plug and play monitor. The BLANK screen is displayed. Press BLANK button on the remote control. 21 Video screen The FREEZE function
  • Hitachi CP-X3010 | Operation Guide - Page 63
    Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect for the ECO MODE item in the SETUP menu. The lamp is approaching the end of its product lifetime. Replace the lamp. Pictures appear blurry. Either the focus
  • Hitachi CP-X3010 | Operation Guide - Page 64
    (R, L RCA x2 Others USB USB-B x1 CONTROL D-sub 9 pin x1 Lamp: DT01021 Filter set: MU06481 Mounting accessary: H AS-3010 (Bracket for ceiling mount) HAS-204L (Fixing adaptor for low ceilings) HAS-304H (Fixing adaptor for high ceilings) Soft case: CA3010 * For more information, please consult your
  • Hitachi CP-X3010 | Operation Guide - Page 65
    Specifications (continued) Specifications 98 113 288 317 [unit: mm] 65
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
1
Projector
CP-X2010/CP-X2510/CP-X3010
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read “
Safety Guide
” first. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
• Mac
®
is a registered trademark of Apple Inc.
• Windows
®
is a registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
All other trademarks are the properties of their respective owners.
NOTICE
This entry notices of fear of causing trouble.