Homelite UTi2100 Operation Manual - Page 17

OPERATION the generator, remove all loads from the generator and press the reset button (see fig. 1). Add loads back to the generator one at a time being careful not to exceed the generators wattage rating. Lubricant: The oil indicator will light and the engine will automatically shut off whenever the lubricant level in the engine becomes low. The engine may not be restarted until sufficient engine lubricant has been added to the generator. NOTE: It is normal for the indicator lights to illuminate and/ or blink each time the engine is started. Once the engine warms up, the lights should default to the pattern above. CHECKING/ADDING LUBRICANT See Figures 3 and 4. NOTICE: Attempting to start the engine before it has been properly filled with lubricant will result in equipment failure. Engine lubricant has a major influence on engine performance and service life. For general, all-temperature use, SAE 10W40 is recommended. Always use a 4-stroke motor lubricant that meets or exceeds the requirements for API service classification SJ. NOTE: Non-detergent or 2-stroke engine lubricants will damage the engine and should not be used. n Loosen the screw on the side cover. Remove side cover and set aside. n Unscrew the oil cap/dipstick and remove. n Wipe dipstick clean and re-seat in hole; do not re-thread. n Remove dipstick again and check lubricant level. Lubricant level should fall between the minimum and maximum marks on the dipstick. n If level is low, add engine lubricant until the fluid level rises between the minimum and maximum marks on the dipstick. n Replace and secure the oil cap/dipstick. n Reinstall the side cover. Tighten screw to secure. USING FUEL STABILIZER Fuel gets old, oxidizes, and breaks down over time. Adding a fuel stabilizer (not included) extends the usable life of fuel and helps prevent deposits from forming that can clog the fuel system. Follow fuel stabilizer manufacturer's directions for correct ratio of stabilizer to fuel.  Mix fuel stabilizer and gasoline prior to filling the tank by using a gas can or other approved fuel container and shaking gently to combine. NOTE: To control the amount of fuel stabilizer being added to the engine, always mix fuel stabilizer with gasoline before fueling the tank rather than adding fuel stabilizer directly into the generator's fuel tank. n Replace and secure the fuel tank cap. n Start and run the engine for at least 5 minutes to allow stabilizer to treat the entire fuel system. OXYGENATED FUELS NOTICE: Do not use E15 or E85 fuel (or fuel containing greater than 10% ethanol) in this product. It is a violation of federal law and will damage the unit and void your warranty. Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentage of oxygenates stated below are not covered under warranty. Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) is acceptable. E15 and E85 are not. CHECKING/ADDING FUEL See Figure 5. WARNING: Gasoline and its vapors are highly flammable and explosive. To prevent serious personal injury and property damage, handle gasoline with care. Keep away from ignition sources, handle outdoors only, do not smoke while adding fuel, and wipe up spills immediately. When adding gas to the generator, make sure the unit is sitting on a flat, level surface. If the engine is hot, let the generator cool for at least five minutes before adding gas. ALWAYS fill the fuel tank outdoors with the machine turned off. n Remove the fuel cap slowly. n Put the on/off switch in the ON ( I ) position. n Fill the fuel tank to 1 in. below the top of the fuel neck. n Replace and secure the fuel cap. NOTE: Always use unleaded gasoline with a pump octane rating of 86 or higher. Never use old, stale, or contaminated gasoline, and do not use an oil/gas mixture. Do not allow dirt or water into the fuel tank. Do not use E85 fuel. OPENING AND CLOSING VENTED FUEL CAP See Figures 6 - 7. The generator has a fuel cap with a vent that can be opened and closed. n To open the vent, rotate the fuel cap lever to the ON (I) position. The vent should be open during operation. n To close the vent, rotate the fuel cap lever to the OFF (O) position. The vent should be closed when the generator is not in use. 13 - English